Nissan Murano. Instruction — part 1285
FRONT PASSENGER AIR BAG MODULE
SR-45
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000009720415
Removal and Installation
INFOID:0000000009720416
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the glove box lid assembly. Refer to
IP-15, "Removal and Installation"
2.
Remove the Instrument lower assist panel. Refer to
IP-15, "Removal and Installation"
.
3.
Disconnect the front passenger air bag harness connector (A).
4.
Remove the front passenger air bag module fixing bolt (B).
NOTE:
The figure shows the installed front passenger air bag module.
(Under view of the module installed without glove box cover.)
5.
Remove the instrument panel assembly (1). Refer to
IP-15, "Removal and Installation"
.
1.
Instrument panel assembly
2.
Front passenger air bag module
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSHIA0060GB
JMHIA0510ZZ
SR-46
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
FRONT PASSENGER AIR BAG MODULE
6.
Remove the front passenger air bag module fixing screws (B).
7.
Disconnect the pawls (C) by using remover tool (A), and then
remove the front passenger air bag module (2) from instrument
panel.
CAUTION:
• Always place the front passenger air bag module with pad
side facing upward.
• Never impact the passenger air bag module.
• Replace the front passenger air bag module if it has been
dropped or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
• Never disassembly the front passenger air bag module.
• Never expose the front passenger air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-
ule.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0511ZZ
: Upward
JMHIA0512ZZ
JMHIA0009ZZ
FRONT SIDE AIR BAG MODULE
SR-47
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT SIDE AIR BAG MODULE
Exploded View
INFOID:0000000009720417
Removal and Installation
INFOID:0000000009720418
REMOVAL
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
• Always work from the rear of the front side air bag module.
• Never use the air tools or electric tools for servicing.
1.
Remove the front seat. Refer to
SE-98, "Removal and Installation"
2.
Remove the seatback board. Refer to
.
3.
Remove the front side air bag module fixing nuts, and/or harness connector.
4.
Remove the front side air bag module.
CAUTION:
• Always place the front side air bag module with pad side fac-
ing upward.
• Never impact the front side air bag module.
1.
Seatback flame
2.
Seat cushion flame
3.
Front side air bag module
A.
Front side air bag harness connector
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JMHIA0514GB
: Upward
JMHIA0274ZZ
SR-48
< REMOVAL AND INSTALLATION >
[FOR MEXICO]
FRONT SIDE AIR BAG MODULE
• Replace the front side air bag module if it has been dropped
or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into front side air bag module.
• Never disassemble the front side air bag module.
• Never expose the front side air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the front side air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use the old fixing nuts after removal, replace with the new nuts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no malfunctioning system is detected by air bag warning
lamp.
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст