Nissan Murano. Instruction — part 1240
B2601 SHIFT POSITION
SEC-57
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK CVT SHIFT SELECTOR CIRCUIT (BCM)
1.
Disconnect BCM connector and IPDM E/R connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)
1.
Check continuity between CVT shift selector (detention switch) harness connector and IPDM E/R harness
connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness or connector.
5.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
SEC-58, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace CVT shift selector. Refer to
TM-167, "Removal and Installation"
6.
CHECK INTERMITTENT INCIDENT
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
8
M122
96
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
8
Not existed
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
9
M122
99
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
9
Not existed
CVT shift selector (detention switch)
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M57
9
E11
43
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
9
Not existed
SEC-58
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2601 SHIFT POSITION
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000009722767
1.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector connector.
3.
Check continuity between CVT shift selector (detention switch) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace CVT shift selector. Refer to
TM-167, "Removal and Installation"
CVT shift selector (detention switch)
Condition
Continuity
Terminal
8
9
Selector lever
P position
Not existed
Other than above
Existed
B2602 SHIFT POSITION
SEC-59
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2602 SHIFT POSITION
Description
INFOID:0000000009722768
BCM confirms the shift position with the following 4 signals.
• CVT shift selector (detention switch)
• Transmission range switch
• P position signal from IPDM E/R (CAN)
• P position signal from TCM (CAN)
DTC Logic
INFOID:0000000009722769
DTC DETECTION LOGIC
NOTE:
• If DTC B2602 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2602 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine under the following conditions and wait for at least 10 seconds.
-
Selector lever is in the P or N position
-
Depress the brake pedal.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009722770
1.
CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT”
Check “Self diagnostic result” with CONSULT. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK CVT SHIFT SELECTOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector (detention switch) connector.
3.
Check voltage between CVT shift selector (detention switch) harness connector and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2602
SHIFT POSITION
BCM detects the following status for 10 seconds.
• Shift position is in P position
• Vehicle speed is 4 km/h (2.5 MPH) or more
• Ignition switch is in the ON position
• Harness or connectors
(CVT shift selector circuit is open
or shorted)
• CVT shift selector (detention
switch)
• ABS actuator and electric unit
(control unit)
• BCM
(+)
(–)
Voltage (V)
(Approx.)
CVT shift selector (detention switch)
Connector
Terminal
M57
8
Ground
Battery voltage
SEC-60
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
NO
>> Repair or replace harness or connector.
4.
CHECK CVT SHIFT SELECTOR CIRCUIT
1.
Disconnect BCM connector and IPDM E/R connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness or connector.
5.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
SEC-58, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace CVT shift selector. Refer to
TM-167, "Removal and Installation"
6.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
8
M122
96
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
8
No existed
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M57
9
M122
99
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M57
9
No existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст