Nissan Murano. Instruction — part 1344
ST-70
< PRECAUTION >
[WITHOUT HEATED STEERING WHEEL]
PRECAUTIONS
"SEAT BELT PRE-TENSIONER"
INFOID:0000000009721516
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR MEXICO : Precautions for Removing of Battery Terminal
INFOID:0000000009956986
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
PREPARATION
ST-71
< PREPARATION >
[WITHOUT HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009721517
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST27180001
(J-25726-A)
Steering wheel puller
Removing steering wheel
ST3127S000
(J-25765-A)
Preload gauge
• Measuring steering column rotating torque
• Measuring pinion rotating torque
• Measuring ball joint rotating torque
KV48104400
(
—
)
Teflon ring correcting tool
a: 50 mm (1.97 in) dia.
b: 36 mm (1.42 in) dia.
c: 100 mm (3.94 in)
Installing rack Teflon ring
KV48103400
(
—
)
Preload adapter
Measuring pinion rotating torque
ST35300000
(
—
)
Drift
a: 45.1 mm (1.776 in) dia.
b: 59.0 mm (2.323 in) dia.
Installing oil pump oil seal
ZZA0819D
ZZA0806D
S-NT550
ZZA0824D
ZZA0881D
ST-72
< PREPARATION >
[WITHOUT HEATED STEERING WHEEL]
PREPARATION
Commercial Service Tools
INFOID:0000000009721518
KV48103500
(J-26357)
Oil pressure gauge
Measuring oil pump relief pressure
KV48102500
(J-33914)
Oil pressure gauge adapter
Measuring oil pump relief pressure
Tool number
(Kent-Moore No.)
Tool name
Description
S-NT547
S-NT542
Tool name
Description
Power tool
Loosening bolts and nuts
Ball joint remover
Removing steering outer socket
Open head
Tightening end cover assembly
PBIC0190E
S-NT146
ZZA0822D
PREPARATION
ST-73
< PREPARATION >
[WITHOUT HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Drift
a: 15 mm (0.59 in) dia.
b: 10 mm (0.39 in) dia.
Installing rotor snap ring
Drift
a: 36 mm (1.42 in) dia.
b: 20 mm (0.79 in) dia.
Installing oil pump oil seal
Tool name
Description
S-NT474
S-NT474
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст