Nissan Murano. Instruction — part 1150
RAX-8
< REMOVAL AND INSTALLATION >
[2WD]
REAR WHEEL HUB AND HOUSING
CAUTION:
Temporarily tighten nuts to prevent damage to threads and to prevent the ball joint remover from
coming off.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub and bearing assembly and steering knuckle.
• Never reuse cotter pin.
Inspection
INFOID:0000000009720602
INSPECTION AFTER REMOVAL
Wheel Hub and Bearing Assembly
Check the wheel hub and bearing assembly for wear, cracks, and damage. Replace if necessary.
Axle Housing
Check the axle housing for wear, cracks, and damage. Replace if necessary.
Ball Joint Inspection
Check for boot breakage, axial looseness, and torque of suspension arm ball joint. Refer to
.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Adjust parking brake operation (stroke). Refer to
PB-3, "Inspection and Adjustment"
.
3.
Check wheel alignment. Refer to
4.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-9
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000009720603
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
RAX-10
< SYMPTOM DIAGNOSIS >
[AWD]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009720604
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
—
—
NVH in DLN section
NVH in DLN section
NVH in RAX
and RSU
sections
Refer to REAR AXLE i
n
t
h
is chart
NVH in WT
section
NVH in WT
section
Ref
e
r t
o
DRIVE
SHAFT
in this
chart
NVH in BR
section
Possible cause and SUSPECTED PARTS
Ex
ce
ss
iv
e j
oi
nt
an
gl
e
Jo
in
t s
lid
in
g re
si
st
an
ce
Imb
al
anc
e
Im
p
rop
er i
n
s
ta
lla
tio
n
,
loo
s
en
es
s
P
a
rt
s interference
PR
OP
EL
LE
R
S
H
A
F
T
DIFFERENTIAL
REA
R
AXLE AND REAR S
U
SPENSION
REA
R
AXLE
TI
RE
ROAD W
H
EEL
DRIV
E SHAFT
BR
AK
E
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
REAR AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
PRECAUTIONS
RAX-11
< PRECAUTION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PRECAUTION
PRECAUTIONS
Precautions for Drive Shaft
INFOID:0000000009720605
• Observe the following precautions when disassembling and assembling drive shaft.
• Never disassemble joint sub-assembly because it is non-overhaul parts.
• Perform work in a location which is as dust-free as possible.
• Clean the parts, before disassembling and assembling.
• Prevent the entry of foreign objects during disassembly of the service location.
• Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
• Use paper waste. Do not use fabric shop cloths because of the danger of lint adhering to parts.
• Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper waste.
Precautions for Removing of Battery Terminal
INFOID:0000000009956970
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст