Nissan Murano. Instruction — part 1149
RAX-4
< PRECAUTION >
[2WD]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Removing of Battery Terminal
INFOID:0000000010062755
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
PREPARATION
RAX-5
< PREPARATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000009720598
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
RAX-6
< PERIODIC MAINTENANCE >
[2WD]
REAR WHEEL HUB AND HOUSING
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Inspection
INFOID:0000000009720599
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular condi-
tions. If there is any of irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
.
REAR WHEEL HUB AND HOUSING
RAX-7
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000009720600
Removal and Installation
INFOID:0000000009720601
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-124, "REAR WHEEL SENSOR : Exploded
.
3.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-48, "BRAKE CALIPER ASSEMBLY : Exploded View"
CAUTION:
Never depress brake pedal while caliper assembly is removed.
4.
Remove disc rotor. Refer to
BR-49, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
5.
Remove cotter pin, then loosen suspension arm mounting nut of axle housing. Refer to
6.
Remove wheel hub and bearing assembly.
7.
Remove parking brake shoe and parking brake cable from back plate. Refer to
8.
Remove anchor block mounting nuts, and then remove anchor block and back plate from axle housing.
9.
Remove stabilizer connecting rod (upper side) with power tool. Refer to
.
10. Remove radius rod (axle housing side). Refer to
11. Remove coil spring. Refer to
12. Set suitable jack under axle housing.
13. Remove front lower link (shock absorber side) with power tool. Refer to
14. Remove front lower link (axle housing side). Refer to
.
15. Separate suspension arm from axle housing so as not to damage ball joint boot using ball joint remover,
and then remove axle housing from the vehicle.
1.
Ball seat
2.
Bushing
3.
Cotter pin
4.
Axle housing
5.
Hub cap
6.
Back plate
7.
Anchor block
8.
Wheel hub and bearing assembly
Refer to
JSDIA2891GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст