Nissan Murano. Instruction — part 424
PREPARATION
DLK-307
< PREPARATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009719210
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009719211
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-50397)
NISSAN Squeak and Rat-
tle Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls, and metal clips
Power tool
SIIA0995E
JMKIA3050ZZ
PIIB1407E
DLK-308
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
REMOVAL AND INSTALLATION
HOOD
HOOD ASSEMBLY
HOOD ASSEMBLY : Exploded View
INFOID:0000000009719212
HOOD ASSEMBLY : Removal and Installation
INFOID:0000000009719213
REMOVAL
1.
Support hood lock assembly with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding hood open when removing hood stay.
2.
Remove the metal clip (3) located on the connection between
the hood stay (1) and the stud ball (2) (hood side), by using a
flatted-blade screwdriver (A).
3.
Disengage the stud ball from the hood stay (hood side).
1.
Hood assembly
2.
Hood front seal
3.
Hood insulator
4.
Hood stay
5.
Hood hinge
6.
Stud ball
7.
Hood bumper rubber
8.
Radiator core seal
Refer to
for symbols in the figure.
JMKIA1797ZZ
JMKIA2255ZZ
HOOD
DLK-309
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4.
Remove hood hinge mounting nuts on the hood to remove the hood assembly.
CAUTION:
Perform work with 2 workers, because of its heavy weight.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• Before installing the hood hinge, apply anticorrosive agent onto the mounting surface of the vehicle
body.
• After installing, perform hood fitting adjustment. Refer to
DLK-309, "HOOD ASSEMBLY : Adjust-
HOOD ASSEMBLY : Adjustment
INFOID:0000000009719214
1.
Hood assembly
2.
Hood bumper rubber side
3.
Hood hinge
4.
Hood lock assembly
5.
Front grille
6.
Front fender
Refer to
JMKIA1834GB
DLK-310
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
Check the clearance and the surface height between hood and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Remove hood lock and adjust the height by rotating hood bumper rubber side until hood becomes 1 to1.5
mm (0.039 to 0.059 in) lower than fender.
2.
Temporarily tighten hood lock, and position by engaging it with hood striker. Check hood lock and striker
for looseness and adjust the clearance and evenness with striker to satisfy the specification.
3.
Adjust A and B shown in the figure to the following value with hood's own weight by dropping it from
approximately 200 mm (7.874 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5lb)].
4.
After adjustment tighten lock bolts to the specified torque.
HOOD HINGE
Portion
Standard
Difference
(RH/LH)
Hood – Front grille
A – A
D
Clearance
3.4 – 7.4 (0.134 – 0.291)
—
E Surface height - 1.4 – 2.6 (- 0.055 – 0.102)
—
Hood – Front fender
B – B
F
Clearance
2.4 – 5.0 (0.094 – 0.197)
< 1.5 (0.059)
G Surface height - 1.3 – 1.3 (- 0.051 – 0.051)
—
C – C
H
Clearance
2.7 – 4.7 (0.106 – 0.185)
< 1.5 (0.059)
I
Surface height - 1.4 – 1.4 (- 0.055 – 0.055)
—
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
A
: 20.0 mm (0.787 in)
B
: 6.8 mm (0.268 in)
PIIB5794E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст