Nissan Murano. Instruction — part 425
HOOD
DLK-311
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD HINGE : Exploded View
INFOID:0000000009719215
HOOD HINGE : Removal and Installation
INFOID:0000000009719216
REMOVAL
1.
Remove hood assembly. Refer to
DLK-308, "HOOD ASSEMBLY : Removal and Installation"
2.
Remove front fender. Refer to
DLK-316, "Removal and Installation"
3.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Before installation of hood hinge, apply anticorrosive agent onto the mounting surface of the vehicle
body.
• After installation, apply touch-up paint (the body color) onto the head of the hinge mounting bolts
and nuts.
• After installation, perform hood fitting adjustment. Refer to
DLK-309, "HOOD ASSEMBLY : Adjust-
HOOD STAY
1.
Hood assembly
2.
Hood front seal
3.
Hood insulator
4.
Hood stay
5.
Hood hinge
6.
Stud ball
7.
Hood bumper rubber
8.
Radiator core seal
Refer to
JMKIA1797ZZ
DLK-312
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
HOOD STAY : Exploded View
INFOID:0000000009719217
HOOD STAY : Removal and Installation
INFOID:0000000009719218
REMOVAL
1.
Remove the metal clip (3) located on the connection between
the hood stay (1) and the stud ball (2) (hood side), by using a
flat-bladed screwdriver (A).
2.
Disengage the stud ball from the hood stay (hood side).
3.
Repeat the same operation to disengage the stud ball from the
hood stay (body side), then remove the hood stay.
INSTALLATION
Install in the reverse order of removal.
1.
Hood assembly
2.
Hood front seal
3.
Hood insulator
4.
Hood stay
5.
Hood hinge
6.
Stud ball
7.
Hood bumper rubber
8.
Radiator core seal
Refer to
for symbols in the figure.
JMKIA1797ZZ
JMKIA2255ZZ
HOOD
DLK-313
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD STAY : Disposal
INFOID:0000000009719219
1.
Fix hood stay (1) using a vise (C).
2.
Using hacksaw (A) slowly make 2 holes in the hood stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on hood stay, always cover a hack-
saw using a shop cloth (B) to avoid scattering metal frag-
ments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
JMKIA3336ZZ
A:
20 mm (0.787 in)
B:
Cut at the groove.
JMKIA3609ZZ
DLK-314
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000009719220
Removal and Installation
INFOID:0000000009719221
REMOVAL
1.
Use a refrigerant collecting equipment to discharge the refrigerant. Refer to
.
2.
Remove front under cover. Refer to
EXT-29, "Removal and Installation"
3.
Drain engine coolant from radiator. Refer to
4.
Remove front grille. Refer to
EXT-21, "Removal and Installation"
5.
Remove front bumper fascia, energy absorber, bumper reinforcement. Refer to
.
6.
Remove air duct assembly. Refer to
.
7.
Remove hood lock. Refer to
DLK-338, "Removal and Installation"
8.
Remove front combination lamp (RH/LH). Refer to
EXL-179, "Removal and Installation"
(XENON TYPE)
EXL-360, "Removal and Installation"
(HALOGEN TYPE).
9.
Disconnect connector of refrigerant pressure sensor. Refer to
.
10. Remove bumper retainer assembly. Refer to
EXT-15, "Removal and Installation"
11. Remove clips, and then remove air guide center and air guide upper.
12. Disengage harness clip from air guide side (RH).
13. Disengage pawls, and then remove air guide side (RH/LH).
14. Remove condenser. Refer to
HA-50, "Removal and Installation"
.
1.
Air guide upper
2.
Air guide side (RH/LH)
3.
Radiator core support
4.
Air guide center
: Pawl
JMKIA1805ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст