Nissan Murano. Instruction — part 1190
REAR SUSPENSION MEMBER
RSU-19
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
19. Remove front lower link. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
rear suspension assembly.
• Check wheel sensor harness for proper connection. Refer to
.
• Never reuse cotter pin.
Inspection
INFOID:0000000009721448
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Adjust parking brake operation (stroke). Refer to
PB-3, "Inspection and Adjustment"
3.
Check wheel alignment. Refer to
4.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
RSU-20
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000009721449
FOR USA AND MEXICO MODELS
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
FOR CANADA MODELS
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000009721450
Wheelarch Height
INFOID:0000000009721451
FOR USA MODELS
Item
Standard
Camber
Degree minute (Decimal degree)
Minimum
–1
°
13
′
(–1.21
°
)
Nominal
–0
°
43
′
(–0.72
°
)
Maximum
–0
°
13
′
(–0.21
°
)
Toe-in
Total toe-in
Distance
Minimum
In 0.9 mm (0.035 in)
Nominal
In 2.7 mm (0.106 in)
Maximum
In 4.5 mm (0.177 in)
Total toe-angle
Degree minute (Decimal degree)
Minimum
In 0
°
04
′
(In 0.07
°
)
Nominal
In 0
°
12
′
(In 0.20
°
)
Maximum
In 0
°
20
′
(In 0.33
°
)
Item
Standard
Camber
Degree minute (Decimal degree)
Minimum
–1
°
11
′
(–1.18
°
)
Nominal
–0
°
41
′
(–0.68
°
)
Maximum
–0
°
11
′
(–0.18
°
)
Toe-in
Total toe-in
Distance
Minimum
In 0.9 mm (0.035 in)
Nominal
In 2.7 mm (0.106 in)
Maximum
In 4.5 mm (0.177 in)
Total toe-angle
Degree minute (Decimal degree)
Minimum
In 0
°
04
′
(In 0.07
°
)
Nominal
In 0
°
12
′
(In 0.20
°
)
Maximum
In 0
°
20
′
(In 0.33
°
)
Item
Standard
Swing torque
0.5 – 3.4 N·m (0.06 – 0.34 kg-m, 5 – 30 in-lb)
Measurement on spring balance (cotter pinhole position)
8.1 – 54.8 N (0.83 – 5.6 kg, 1.82 – 12.32 lb)
Axial end play
0 mm (0 in)
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-21
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
FOR CANADA MODELS
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
FOR MEXICO MODELS
Item
Standard
Axle type
2WD
AWD
Wheel size
18 inch
20 inch
18 inch
20 inch
Grade
S
SL
LE
S
SL
LE
Front (Hr)
846 mm (33.31 in)
845 mm (33.27 in)
846 mm (33.31 in)
845 mm (33.27 in)
Rear (Hr)
859 mm (33.82 in)
858 mm (33.78 in)
858 mm (33.78 in)
857 mm (33.74 in)
SFA746B
Item
Standard
Wheel size
18 inch
20 inch
Grade
S
SL
LE
Front (Hr)
845 mm (33.27 in)
846 mm (33.31 in)
Rear (Hr)
858 mm (33.78 in)
857 mm (33.74 in)
SFA746B
Item
Standard
Axle type
2WD
AWD
Grade
S
SL
LE
Front (Hr)
846 mm (33.31 in)
845 mm (33.27 in)
RSU-22
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Rear (Hr)
859 mm (33.82 in)
858 mm (33.78 in)
857 mm (33.74 in)
Item
Standard
Axle type
2WD
AWD
Grade
S
SL
LE
SFA746B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст