Nissan Murano. Instruction — part 1189
REAR STABILIZER
RSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR STABILIZER
Exploded View
INFOID:0000000009721440
Removal and Installation
INFOID:0000000009721441
REMOVAL
1.
Remove tires with power tool.
2.
Remove stabilizer connecting rod.
CAUTION:
Apply a matching mark to identify the installation position.
3.
Remove mounting bolts on stabilizer clamp and remove stabilizer bar with power tool.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Check the matching mark when installing.
• Tighten the mounting nut to the specified torque while holding a hexagonal part of stabilizer connecting rod
side.
Inspection
INFOID:0000000009721442
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer bushing, stabilizer clamp, stabilizer connecting rod, for any deformation, crack
or damage. Replace if necessary.
1.
Suspension arm
2.
Stabilizer connecting rod
3.
Stabilizer bar
4.
Stabilizer bushing
5.
Stabilizer clamp
for symbols in the figure.
JPEIB0268GB
RSU-16
< REMOVAL AND INSTALLATION >
REAR SUSPENSION ARM
REAR SUSPENSION ARM
Exploded View
INFOID:0000000009721443
NOTE:
Remove suspension arm with rear suspension member for AWD models. Refer to
.
Removal and Installation
INFOID:0000000009721444
NOTE:
Remove suspension arm with rear suspension member for AWD models. Refer to
.
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-124, "REAR WHEEL SENSOR : Exploded
.
3.
Remove stabilizer connecting rod. Refer to
.
4.
Remove cotter pin of suspension arm ball joint, and loosen nut.
5.
Use the ball joint remover to remove suspension arm from axle housing. Be careful not to damage ball
joint boot.
CAUTION:
Tighten temporarily mounting nut to prevent damage to threads and to prevent ball joint remover
from coming off.
6.
Remove suspension arm.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member installation position (rubber bushing), under unladen
conditions with tires on level ground.
Inspection
INFOID:0000000009721445
INSPECTION AFTER REMOVAL
Appearance
Check the following items, and replace the part if necessary.
• Suspension arm and bushing for deformation, cracks or damage.
• Boot of ball joint for cracks or damage, and also for grease leakage.
1.
Suspension arm
2.
Stopper rubber
3.
Rear suspension member
Refer to
for symbols in the figure.
JPEIB0141GB
REAR SUSPENSION ARM
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Ball Joint Inspection
Instructionly move ball stud at least ten times by hand to check for smooth movement.
Swing Torque Inspection
1.
Before measurement, move ball stud at least ten times by hand to check for smooth movement.
2.
Hook spring balance (A) at cotter pin mounting hole. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
-
If swing torque exceeds the standard range, replace suspension
arm assembly.
Axial End Play Inspection
1.
Before measurement, move ball stud at least ten times by hand to check for smooth movement.
2.
Move tip of ball stud in axial direction to check for looseness.
-
If axial end play exceeds the standard range, replace suspension arm assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Swing torque
: Refer to
.
JPEIA0005ZZ
Axial end play
: Refer to
.
RSU-18
< UNIT REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
UNIT REMOVAL AND INSTALLATION
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000009721446
Removal and Installation
INFOID:0000000009721447
REMOVAL
1.
Remove tires with power tool.
2.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-48, "BRAKE CALIPER ASSEMBLY : Exploded View"
CAUTION:
Avoid depressing brake pedal while caliper assembly is removed.
3.
Remove wheel sensor and sensor harness. Refer to
BRC-124, "REAR WHEEL SENSOR : Exploded
.
4.
Remove center muffler. Refer to
5.
Remove stabilizer bar. Refer to
6.
Remove drive shaft (AWD models). Refer to
.
7.
Remove propeller shaft (AWD models). Refer to
.
8.
Remove harness from rear final drive and rear suspension member (AWD models).
9.
Remove rear final drive (AWD models). Refer to
.
10. Separate the attachment between parking brake cable and vehicle and rear suspension member. Refer to
.
11. Remove rear lower link and coil spring. Refer to
12. Remove shock absorber (lower side). Refer to
13. Set suitable jack under rear suspension member.
14. Remove member stay.
15. Remove rear suspension member and rebound stopper.
16. Slowly lower jack, then remove rear suspension member, suspension arm, radius rod, front lower link and
axle from vehicle as a unit.
17. Remove suspension arm. Refer to
18. Remove radius rod. Refer to
1.
Rebound stopper
2.
Rear suspension member
3.
Member stay
Refer to
for symbols in the figure.
JPEIB0148GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст