Nissan Murano. Instruction — part 915
LUGGAGE FLOOR TRIM
INT-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
4.
After removal, place the luggage rear plate (1) as shown in the
figure, then with a screwdriver (A) remove the luggage rear plate
cap fixing bolts (B) and then remove the cap.
5.
Remove the rear plate ornament (2) from the rear plate (1) as shown in the figure below.
6.
Remove the bolts located inside the luggage floor spacer and remove luggage floor spacer (LH and RH).
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Check that clips, pawls, metal clips are securely fitted in panel holes on body when installing, and then
press them in.
JMJIA1406ZZ
: Clip
JMJIA1407ZZ
INT-38
< REMOVAL AND INSTALLATION >
BACK DOOR TRIM
BACK DOOR TRIM
Exploded View
INFOID:0000000009720378
Removal and Installation
INFOID:0000000009720379
REMOVAL
BACK DOOR FINISHER INNER
1.
Fully open back door.
2.
Disengage pull handle finisher (1) fixing pawls with remover tool
(A) and then remove pull handle finisher.
1.
Back door assembly
2.
Back door hinge cover (LH/RH)
3.
Back door plate
4.
Back door finisher inner
5.
Back door finisher lid
6.
Pull handle finisher
7.
Auto power back door switch finisher 8.
Back door upper cover
: Clip
: Pawl
: Metal clip
JMJIA2570ZZ
: Pawl
JMJIA0621ZZ
BACK DOOR TRIM
INT-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3.
Push the clip center with a wrapped flat-blade screwdriver (B)
and then remove clip (A).
4.
Disengage the luggage room lamp fixing pawls with a tool, dis-
connect the harness connector (A) then remove the lamps (1)
(LH and RH)
5.
Disengage the back door finisher lid (1) fixing pawls, then
remove the back door finisher lid with remover tool (A).
6.
Remove the auto power back door switch finisher (1) by using
remover tool (A) and then remove auto power door switch fin-
isher.
7.
Remove the back door finisher inner.
NOTE:
It is strongly recommended to follow the steps below when removing the back door finisher. Failing to do
so may damage the clips.
JMJIA1018ZZ
JMJIA1385ZZ
: Pawl
JMJIA1384ZZ
: Pawl
JMJIA1383ZZ
INT-40
< REMOVAL AND INSTALLATION >
BACK DOOR TRIM
1.
Insert remover tool (A) between back door finisher inner (1)
and back door panel to disengage the metal clips (LH and
RH).
2.
Insert remover tool (A) between back door finisher inner (1)
and back window glass, pull downwards to disengage clips
as shown in the figure.
3.
Insert remover tool (A) between back door lower finisher
inner (1) and back door panel to disengage the clips.
NOTE:
Start from the lower-downward side and work around the
edges and up to the sides.
8.
Pull out to remove back door finisher inner.
9.
Disengage back door plate (1) fixing pawls and metal clips with
remover tool (A) and then remove back door plate.
: Metal clip
JMJIA1673ZZ
: Clip
: Metal clip
JMJIA1674ZZ
: Clip
JMJIA0622ZZ
: Pawl
: Metal clip
JMJIA1691ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст