Nissan Murano. Instruction — part 910
DOOR FINISHER
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
REAR DOOR FINISHER : Removal and Installation
INFOID:0000000009720367
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
REMOVAL
1.
Fully open rear door window.
2.
Remove inside handle escutcheon (1) with remover tool (A).
3.
Remove bolt (B) located behind the inside handle escutcheon
with tool (A).
4.
Disengage the power window switch finisher (1) fixing pawls
with a remover tool (A).
5.
Disconnect power window switch connector, and then remove power window switch finisher.
1.
Inside handle escutcheon
2.
Step lamp
3.
Power window switch finisher
4.
Rear door finisher
5.
Rear door inside handle
6.
Rear heated seat switch finisher
7.
Rear door panel
8.
Rear door inside seal
9.
Armrest finisher
10. Power window switch
: Clip
: Pawl
: Pawl
JMJIA1350ZZ
JMJIA1351ZZ
: Pawl
JMJIA1361ZZ
INT-18
< REMOVAL AND INSTALLATION >
DOOR FINISHER
6.
Remove bolt (B) located behind power window switch finisher
with tool (A).
7.
Remove armrest finisher (1) with remover tool (A).
8.
Remove bolt (B) located behind armrest finisher with tool (A).
9.
Remove rear heated seat (LH/RH) switch finisher with remover tool, and then disconnect the harness
connectors. (With rear heated seat switch)
10. Insert remover tool (A) between door finisher and door panel to
disengage door finisher mounting clips, starting from the bottom
and working to the top.
11. Pull up rear door finisher and pull out.
JMJIA1354ZZ
: Pawl
JMJIA1355ZZ
JMJIA1356ZZ
: Clip
JMJIA1360ZZ
DOOR FINISHER
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
12. Disconnect lock knob cable (1) and inside handle cable (2) from
rear door inside handle (3).
13. Remove rear door finisher.
14. Remove the inside handle after removing rear door finisher. Refer to
.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
JMJIA1359ZZ
INT-20
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
BODY SIDE TRIM
Exploded View
INFOID:0000000009720368
Removal and Installation
INFOID:0000000009720369
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
• Fabric upholstered parts are easily damaged. Be careful while performing work and storing parts.
• Be careful not to pull out clips forcibly. Otherwise, vehicle body may be deformed.
REMOVAL
FRONT PILLAR GARNISH
1.
Remove front body side welt partially.
2.
Remove front pillar garnish.
1.
Front body side welt
2.
Rear body side welt
3.
Front pillar garnish
4.
Front kicking plate (inner)
5.
Dash side finisher
6.
Rear kicking plate (inner)
7.
Center pillar lower garnish
8.
Center pillar upper garnish
9.
Front kicking plate (outer)
10. Rear kicking plate (outer)
11. Center pillar upper cap
: Clip
: Pawl
: Metal clip
: Always replace after every disassembly.
JMJIA1363ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст