Nissan Murano. Instruction — part 1336
ST-38
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
STEERING COLUMN
9.
Remove knee protector (1).
10. Disconnect each switch harness connectors installed to steering
column assembly.
11. Remove the upper joint mounting bolt and nut (lower shaft side),
and separate the upper joint from lower shaft.
CAUTION:
When removing upper joint, never insert a tool, such as a
screwdriver, into the yoke groove to pull out the upper joint.
In case of the violation of the above, replace upper joint
with a new one.
12. Remove steering column assembly.
CAUTION:
• Never give axial impact to steering column assembly during removal.
• Never move steering gear assembly when removing steering column assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the slide plate (1) and steering column housing (2) so that
the mounting dimensions (L) is within the specified range as
described below.
• Tighten the mounting bolts in the order shown in the figure when
installing the steering column assembly.
• Be careful of the following points when installing the steering col-
umn assembly.
CAUTION:
• Never give axial impact to steering column assembly during
installation.
• Never move steering gear assembly.
• Never reuse the joint mounting nut (lower shaft side).
• Adjust neutral position of steering angle sensor. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Special Repair Requirement"
.
WITHOUT ELECTRIC MOTOR : Inspection
INFOID:0000000009721483
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if necessary.
• Measure steering column assembly rotating torque using a preload gauge [SST: ST3127S000 (J-25765-A)].
Replace steering column assembly if outside the standard.
: Bolt
JSGIA0306ZZ
Standard
L
: 2.0 mm (0.079 in) or less
JSGIA0315ZZ
JSGIA0310ZZ
Standard
Rotating torque
: Refer to
STEERING COLUMN
ST-39
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Measure the length (L) as shown, if vehicle has been involved in a
minor collision. Replace steering column assembly if out side the
standard.
• Install the bracket (1) and steering column housing (2) so that the
clearance (A) is within the specified range as described below.
Replace steering column assembly if out side the standard.
INSPECTION AFTER INSTALLATION
• Check each part of steering column assembly for damage or other malfunctions. Replace if necessary.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
• Check tilt and telescopic mechanism operating range tilt operating
range (T), telescopic operating range (L) as shown in the figure.
WITH ELECTRIC MOTOR
Standard
Steering column length (L)
: Refer to
JSGIA0562ZZ
Standard
Mounting dimensions (A)
: Refer to
JSGIA0389ZZ
Standard
Tilt operating range (T)
: Refer to
"Steering Column Op-
erating Range"
.
Telescopic operating range (L)
: Refer to
"Steering Column Op-
erating Range"
.
JSGIA0307ZZ
ST-40
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
STEERING COLUMN
WITH ELECTRIC MOTOR : Exploded View
INFOID:0000000009721484
WITH ELECTRIC MOTOR : Removal and Installation
INFOID:0000000009721485
REMOVAL
1.
Set the vehicle to the straight-ahead position.
2.
Place the tilt to the highest level. Place the telescopic to the longest level.
3.
Remove driver air bag module. Refer to
.
4.
Remove steering wheel. Refer to
.
5.
Remove instrument driver lower panel. Refer to
.
6.
Remove steering column cover. Refer to
.
7.
Remove spiral cable. Refer to
.
8.
Remove cluster lid A. Refer to
1.
Bracket
2.
Steering column assembly
3.
Bracket
4.
Clip
5.
Tilt motor
6.
Bracket
7.
Bracket
8.
Bracket
9.
Slide bracket
10. Lower mount bracket
11.
Upper joint
12. Bracket
13. Telescopic motor
14. Bracket
15. Bracket
Refer to
for symbols in the figure.
JSGIA0529GB
STEERING COLUMN
ST-41
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
9.
Remove knee protector (1).
10. Disconnect each switch harness connectors installed to steering
column assembly.
11. Remove the upper joint mounting bolt and nut (lower shaft side),
and separate the upper joint from lower shaft.
CAUTION:
When removing upper joint, never insert a tool, such as a
screwdriver, into the yoke groove to pull out the upper joint.
In case of the violation of the above, replace upper joint
with a new one.
12. Remove steering column assembly.
CAUTION:
• Never give axial impact to steering column assembly during removal.
• Never move steering gear assembly when removing steering column assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the slide plate (1) and steering column housing (2) so that
the mounting dimensions (L) is within the specified range as
described below.
• Tighten the mounting bolts in the order shown in the figure when
installing the steering column assembly.
• Be careful of the following points when installing the steering col-
umn assembly.
CAUTION:
• Never give axial impact to steering column assembly during
installation.
• Never move steering gear assembly.
• Never reuse the joint mounting nut (lower shaft side).
• Adjust neutral position of steering angle sensor. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Special Repair Requirement"
WITH ELECTRIC MOTOR : Inspection
INFOID:0000000009721486
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if necessary.
• Measure steering column assembly rotating torque using a preload gauge [SST: ST3127S000 (J-25765-A)].
Replace steering column assembly if outside the standard.
: Bolt
JSGIA0306ZZ
Standard
L
: 2.0 mm (0.079 in) or less
JSGIA0315ZZ
JSGIA0310ZZ
Standard
Rotating torque
: Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст