Nissan Murano. Instruction — part 1337
ST-42
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
STEERING COLUMN
• Measure the length (L) as shown, if vehicle has been involved in a
minor collision. Replace steering column assembly if out side the
standard.
• Install the bracket (1) and steering column housing (2) so that the
clearance (A) is within the specified range as described below.
Replace steering column assembly if out side the standard.
INSPECTION AFTER INSTALLATION
• Check each part of steering column assembly for damage or other malfunctions. Replace if necessary.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check tilt and telescopic mechanism operating range tilt operating
range (T), telescopic operating range (L) as shown in the figure.
Standard
Steering column length (L)
: Refer to
.
JSGIA0563ZZ
Standard
Mounting dimensions (A)
: Refer to
JSGIA0389ZZ
Standard
Tilt operating range (T)
: Refer to
"Steering Column
Operating Range"
.
Telescopic operating range (L)
: Refer to
"Steering Column
Operating Range"
.
JSGIA0309ZZ
LOWER SHAFT
ST-43
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
LOWER SHAFT
Exploded View
INFOID:0000000009721487
Removal and Installation
INFOID:0000000009721488
REMOVAL
1.
Set the vehicle to the straight-ahead position.
2.
Fix the steering wheel.
3.
Remove upper joint fixing bolt and nut (lower shaft side).
4.
Separate the lower shaft from the upper joint by sliding the slide
shaft (A: sliding range).
CAUTION:
• Spiral cable may be cut if steering wheel turns while sepa-
rating steering column assembly and steering column
assembly. Be sure to secure steering wheel using string
to avoid turning.
• When removing upper joint, never insert a tool, such as a
screwdriver, into the yoke groove to pull out the upper
joint. In case of the violation of the above, replace upper
joint with a new one.
5.
Remove the accelerator pedal bracket and lever assembly.
Refer to
6.
Remove the side brake pedal bracket and wire clamp stay.
7.
Remove the hole cover mounting nuts.
8.
Remove the hole cover seal, clamp and hole cover.
9.
Remove lower shaft joint fixing bolt (steering gear side).
10. Remove the lower shaft from steering gear assembly.
CAUTION:
When removing lower shaft, never insert a tool, such as a screwdriver, into the yoke groove to pull
out the lower shaft. In case of the violation of the above, replace lower shaft with a new one.
1.
Steering column assembly
2.
Hole cover seal
3.
Clamp
4.
Hole cover
5.
Lower shaft
Refer to
JSGIA0311GB
JSGIA0312ZZ
ST-44
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
LOWER SHAFT
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Be sure to secure steering wheel using string to avoid turning.
• Tighten the clamp to the specified torque and check the clamp
length (A).
• After lower shaft (steering gear side) fitted, make sure there is not
gap (A) between the yoke (1), lower shaft (2), joint fixing bolt (3).
• When installing lower joint to steering gear assembly, follow the procedure listed below.
- Set rack of steering gear in the neutral position.
NOTE:
To get the neutral position of rack, turn gear-sub assembly and measure the distance of inner socket, and
then measure the intermediate position of the distance.
- Align rear cover cap projection (A) with the marking position of
gear housing assembly (B).
- Install slit part of lower joint (C) aligning with the rear cover cap
projection (A). Make sure that the slit part of lower joint (C) is
aligned with rear cover cap projection (A) and the marking position
of gear housing assembly (B).
• Adjust neutral position of steering angle sensor. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Special Repair Requirement"
.
• Check the following after installation:
- Check if steering wheel turns smoothly when it is turned several times fully to the end of the left and right.
- Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
Clamp length “A”
: 14.0 – 18.0 mm (0.551 –
0.709 in)
JSGIA0094ZZ
JSGIA0180ZZ
: Bolt
JSGIA0313ZZ
LOWER SHAFT
ST-45
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Inspection
INFOID:0000000009721489
• Check the length (A) (extended position) of the lower shaft.
• Check each part of lower shaft for damage or other malfunctions.
Replace if there are.
Standard
Lower shaft length (A)
: Refer to
.
JSGIA0314ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст