Nissan Murano. Instruction — part 1178
RF-96
< REMOVAL AND INSTALLATION >
GLASS LID
FOR HIGH DURABILITY SPECIFICATION
JMKIA6509GB
1.
Roof side finisher RH
2.
Rear link cover
3.
TORX bolt
4.
Glass lid
5.
Inner blind
6.
Sunroof unit assembly
7.
Sunroof bracket
8.
Drain plug
9.
Drain hose
10. Drain connector
11.
Roof side finisher LH
12. Sunroof motor assembly
13. Sunshade motor assembly
14. Deflector knock RH
15. Deflector knock LH
: Pawl
GLASS LID
RF-97
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Removal and Installation
INFOID:0000000009719690
REMOVAL
CAUTION:
Always work with a helper.
1.
Remove the roof rail assembly. Refer to
EXT-31, "Removal and Installation"
2.
Remove the roof side finisher.
Remove the clips, and then pull out roof side finisher.
3.
Half open the glass lid.
4.
Remove the TORX bolts from inner side.
• Remove the inner blind.
• Remove the TORX bolts (A).
5.
Remove the TORX bolts from outer side.
• Remove the pawls, and then pull down rear link cover (1).
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
: Clip
: Pawl
JMKIA6378ZZ
JMKIA1905ZZ
: Pawl
JMKIA1906ZZ
RF-98
< REMOVAL AND INSTALLATION >
GLASS LID
• Remove the TORX bolts (B).
6.
Remove the glass lid from the vehicle.
7.
Remove the deflector knock (LH and RH).
INSTALLATION
CAUTION:
• If deflector knock is not inserted smoothly, add chamfer to the end as shown in the figure. Always
apply anti-corrosion treatment.
• After installing the glass lid, perform the leak test and check that there is no malfunction.
NOTE:
After installation carry out fitting adjustment. Refer to
Install in the reverse order of removal.
Adjustment
INFOID:0000000009719691
WEATHER-STRIP OVERLAP ADJUSTMENT AND SURFACE MISMATCH ADJUSTMENT
1.
Tilt up glass lid, and then remove inner blind and rear link cover.
JMKIA1907ZZ
a
: 1.5mm (0.06 in)
JMKIA6514ZZ
JMKIA6377ZZ
GLASS LID
RF-99
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
2.
After loosening glass lid from TORX bolts (left and right), tilt down glass lid.
3.
Adjust glass lid from outside of vehicle so it resembles “ A – A” “B – B” as shown in the figure.
4.
To prevent glass lid from moving after adjustment, first tighten the TORX bolts of front left, and then
tighten the TORX bolts of rear right.
5.
Tighten remaining TORX bolts, being careful to prevent glass lid from moving.
6.
Tilt glass lid up and down several times to check that it moves smoothly.
NOTE:
After adjustment the sunroof unit assembly, perform additional service. Refer to
VICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
.
Portion
a (Clearance)
b (Surface height)
Glass lid front end
A – A
8.3 mm (0.327 in)
(
−
1.5) – (+1.5) mm
[(
−
0.059) – (+ 0.059) in]
Glass lid rear end
B – B
19.8 mm (0.780 in)
(
−
1.5) – (+1.5) mm
[(
−
0.059) – (+ 0.059) in]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст