Nissan Murano. Instruction — part 1177
RF-92
< PRECAUTION >
PRECAUTIONS
FOR MEXICO : Precaution for Procedure without Cowl Top Cover
INFOID:0000000009719686
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
FOR MEXICO : Precautions For Xenon Headlamp Service
INFOID:0000000010108358
WARNING:
Comply with the following warnings to prevent any serious accident.
• Disconnect the battery cable (negative terminal) or the power supply fuse before installing, remov-
ing, or touching the xenon headlamp (bulb included). The xenon headlamp contains high-voltage
generated parts.
• Never work with wet hands.
• Check the xenon headlamp ON-OFF status after assembling it to the vehicle. Never turn the xenon
headlamp ON in other conditions. Connect the power supply to the vehicle-side connector.
(Turning it ON outside the lamp case may cause fire or visual impairments.)
• Never touch the bulb glass immediately after turning it OFF. It is extremely hot.
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Install the xenon bulb securely. (Insufficient bulb socket installation may melt the bulb, the connec-
tor, the housing, etc. by high-voltage leakage or corona discharge.)
• Never perform HID circuit inspection with a tester.
• Never touch the xenon bulb glass with hands. Never put oil and grease on it.
• Dispose of the used xenon bulb after packing it in thick vinyl without breaking it.
• Never wipe out dirt and contamination with organic solvent (thinner, gasoline, etc.).
FOR MEXICO : Precautions for Removing of Battery Terminal
INFOID:0000000010108357
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
PIIB3706J
SEF289H
PREPARATION
RF-93
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009719687
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000009719688
Tool number
(Kent-Moore No.)
Tool name
Description
(J39570)
Chassis ear
Locates the noise
(J50397)
NISSAN Squeak and Rattle
Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls and metal clips
SIIA0995E
JMKIA3050ZZ
RF-94
< REMOVAL AND INSTALLATION >
GLASS LID
REMOVAL AND INSTALLATION
GLASS LID
Exploded View
INFOID:0000000009719689
FOR STANDARD SPECIFICATION
JMKIA6375GB
GLASS LID
RF-95
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
1.
Roof side finisher RH
2.
Rear link cover
3.
TORX bolt
4.
Glass lid
5.
Inner blind
6.
Sunroof unit assembly
7.
Sunroof bracket
8.
Drain plug
9.
Drain hose
10. Drain connector
11.
Roof side finisher LH
12. Sunroof motor assembly
13. Sunshade motor assembly
14. Deflector knock RH
15. Deflector knock LH
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст