Nissan Murano. Instruction — part 8
ADP-24
< SYSTEM DESCRIPTION >
AUTOMATIC DRIVE POSITIONER SYSTEM
MEMORY FUNCTION : Component Parts Location
INFOID:0000000009720640
1.
BCM M118, M119, M122, M123
2.
Automatic drive positioner control unit
M75, M104
3.
Combination meter
4.
Tilt & telescopic switch M102
5.
Key slot M99
6.
Seat memory switch D13
7.
Door mirror remote control switch
D14
8.
Front door switch (driver side) B34
9.
Tilt motor M116
JMJIA1409ZZ
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-25
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
MEMORY FUNCTION : Component Description
INFOID:0000000009720641
CONTROL UNITS
INPUT PARTS
Switches
10. Telescopic motor M117
11.
Door mirror (driver side) D3
12. Reclining motor B461
13. Sliding, Lifting switch
(Power seat switch B459)
14. Reclining switch
(Power seat switch B459)
15. Driver seat control unit B451,B452
16. Sliding motor B461
17. Lifting motor (front) B455
18. Lifting motor (rear) B456
A.
Behind the combination meter
B.
View with instrument driver lower
panel removed
C.
View with instrument driver lower
panel removed
D.
View with seat cushion and seatback
pad removed
E.
Backside of the seat cushion
Item
Function
Driver seat control unit
• Main units of automatic drive positioner system
• It is connected to the CAN.
• It communicates with the automatic drive positioner control via UART communi-
cation.
Automatic drive positioner control unit
• It communicates with the driver seat control unit via UART communication.
• Perform various controls with the instructions of driver seat control unit.
• Perform the controls of the tilt & telescopic, door mirror switch.
BCM
Transmit the following status to the driver seat control unit via CAN communication.
• Driver door: OPEN/CLOSE
• Ignition switch position: ACC/ON
• Door lock: UNLOCK (with Intelligent Key or driver side door request switch oper-
ation)
• Key ID
• Key switch: Insert/Pull out Intelligent Key
• Starter: CRANKING/OTHER
• Handle position : LHD
Combination meter / ABS
Transmit the vehicle speed signal to the driver seat control unit via CAN communi-
cation.
TCM
Transmit the shift position signal (P range) to the driver seat control unit via CAN
communication.
Item
Function
Key slot
The key switch is installed to detect the key inserted/removed status.
Front door switch (driver side)
Detect front door (driver side) open/close status.
CVT shift selector (detention switch)
Detect the P range position of selector lever.
Set switch
The registration and system setting can be performed with its operation.
Memory switch 1/2
The registration and operation can be performed with its operation.
Power seat switch
The following switch is installed.
• Reclining switch
• Lifting switch (front)
• Lifting switch (rear)
• Sliding switch
The specific parts can be operated with the operation of each switch.
ADP-26
< SYSTEM DESCRIPTION >
AUTOMATIC DRIVE POSITIONER SYSTEM
Sensors
OUTPUT PARTS
EXIT ASSIST FUNCTION
Tilt & telescopic switch
The following switch is installed.
• Tilt switch
• Telescopic switch
The specific parts can be operated with the operation of each switch.
Door mirror remote control switch
The following switch is installed.
• Mirror switch
• Changeover switch
The specific parts can be operated with the operation of each switch.
Item
Function
Item
Function
Door mirror sensor
(driver side/passenger side)
Detect the up/down and left/right position of outside mirror face.
Tilt and telescopic sensor
Detect the up/down and left/right position of steering column.
Lifting sensor (front)
Detect the up/down position of seat lifting (front).
Lifting sensor (rear)
Detect the up/down position of seat lifting (rear).
Reclining sensor
Detect the tilt of seatback.
Sliding sensor
Detect the front/rear position of seat.
Item
Function
Door mirror motor
(driver side/passenger side)
Move the outside mirror face upward/downward and leftward/rightward.
Tilt and telescopic motor
Move the steering column upward/downward and frontward/rearward.
Lifting motor (front)
Move the seat lifting (front) upward/downward.
Lifting motor (rear)
Move the seat lifting (rear) upward/downward.
Reclining motor
Tilt and raise up the seatback.
Sliding motor
Slide the seat frontward/rearward.
Memory indicator
Illuminates or flashes according to the registration/operation status.
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-27
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
EXIT ASSIST FUNCTION : System Diagram
INFOID:0000000009720642
EXIT ASSIST FUNCTION : System Description
INFOID:0000000009720643
OUTLINE
When exiting, the condition is satisfied, the seat is moved backward 40 mm (1.57 in) from normal sitting posi-
tion and the steering is moved to the most upper position.
The seat slide amount and the steering operation at entry/exit operation can be changed.
NOTE:
• This function is set to ON before delivery (initial setting).
• Further information for the system setting procedure. Refer to
ADP-9, "SYSTEM INITIALIZATION : Descrip-
OPERATION PROCEDURE
1.
Open the driver door with ignition switch in OFF position.(Intelligent Key is not inserted into key slot)
2.
Driver seat and steering column will move to the exiting position.
OPERATION CONDITION
Satisfy all of the following items. The exit assist function is not performed if these items are not satisfied.
JMJIA1462GB
Item
Request status
Ignition position
OFF
System setting [Entry/exit assist function (seat/steering)]
ON
Initialization
Done
Key switch
OFF
(Intelligent Key is not inserted into key slot)
Switch inputs
• Power seat switch
• Tilt & telescopic switch
• Door mirror remote control switch
• Set switch
• Memory switch
OFF
(Not operated)
Selector lever
P position
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст