Nissan Murano. Instruction — part 292
DAS-58
< DTC/CIRCUIT DIAGNOSIS >
[LDW]
C1A03 VEHICLE SPEED SENSOR
DTC/CIRCUIT DIAGNOSIS
C1A03 VEHICLE SPEED SENSOR
DTC Logic
INFOID:0000000009723237
DTC DETECTION LOGIC
NOTE:
If DTC “C1A03” is detected along with DTC “U1000” or “C1A04”, first diagnose the DTC “U1000” or “C1A04”.
• Refer to
for DTC “U1000”.
• Refer to
for DTC “C1A04”.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the LDW system ON.
3.
Drive the vehicle at 30 km/h (19 MPH) or more.
CAUTION:
Always drive safety.
4.
Stop the vehicle.
5.
Perform “All DTC Reading” with CONSULT.
6.
Check if the “C1A03” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “C1A03” detected as the current malfunction?
YES
>> Refer to
.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000009723238
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “C1A04” or “U1000” is detected other than “C1A03” in “Self Diagnostic Result” of “AVM”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> Replace the camera control unit. Refer to
DAS-94, "Removal and Installation"
.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
C1A03
VHCL SPEED SE CIRC
If the vehicle speed signal (wheel speed) from
ABS actuator and electric unit (control unit) re-
ceived by the camera control unit via CAN com-
munication, are inconsistent
• Wheel speed sensor
• ABS actuator and electric unit (control
unit)
• Camera control unit
DAS
C1A04 ABS/TCS/VDC SYSTEM
DAS-59
< DTC/CIRCUIT DIAGNOSIS >
[LDW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1A04 ABS/TCS/VDC SYSTEM
DTC Logic
INFOID:0000000009723239
DTC DETECTION LOGIC
NOTE:
If DTC “C1A04” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Wait for approximately 10 minutes after turning the LDW system ON.
3.
Perform “All DTC Reading” with CONSULT.
4.
Check if the “C1A04” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “C1A04” detected as the current malfunction?
YES
>> Refer to
NO
>> Refer to
GI-44, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000009723240
1.
CHECK SELF-DIAGNOSIS RESULTS
1.
Perform “All DTC Reading” with CONSULT.
2.
Check if the “U1000” is detected other than “C1A04” in “Self Diagnostic Result” of “AVM”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
.
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> Replace the camera control unit. Refer to
DAS-94, "Removal and Installation"
.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
C1A04
ABS/TCS/VDC CIRC
If a malfunction occurs in the VDC/TCS/ABS
system
ABS actuator and electric unit (control
unit)
DAS-60
< DTC/CIRCUIT DIAGNOSIS >
[LDW]
C1A39 STEERING ANGLE SENSOR
C1A39 STEERING ANGLE SENSOR
DTC Logic
INFOID:0000000009723241
DTC DETECTION LOGIC
NOTE:
If DTC “C1A39” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the ignition switch ON.
2.
Perform “All DTC Reading” with CONSULT.
3.
Check if the “C1A39” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “C1A39” detected as the current malfunction?
YES
>> Refer to
.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000009723242
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A39” in “Self Diagnostic Result” of “AVM”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> Replace the camera control unit. Refer to
DAS-94, "Removal and Installation"
.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
C1A39
STRG SEN CIR
If the steering angle sensor is malfunction
Steering angle sensor
DAS
U0122 ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
DAS-61
< DTC/CIRCUIT DIAGNOSIS >
[LDW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
U0122 ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
DTC Logic
INFOID:0000000009723243
DTC DETECTION LOGIC
NOTE:
If DTC “U0122” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the LDW system ON.
3.
Perform “All DTC Reading” with CONSULT.
4.
Check if the “U0122” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U0122” detected as the current malfunction?
YES
>> Refer to
NO
>> Refer to
GI-44, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000009723244
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0122” in “Self Diagnostic Result” of “AVM”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
.
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> Replace the camera control unit. Refer to
DAS-94, "Removal and Installation"
.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U0122
VDC P-RUN DIAGNO-
SIS
If camera control unit detects an error signal
that is received from ABS actuator and electric
unit (control unit) via CAN communication
ABS actuator and electric unit (control
unit)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст