Nissan Murano. Instruction — part 912
FLOOR TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
6.
Disengage pawl using a remover tool (A) and open the harness
protector.
7.
Remove floor carpet.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When inserting floor carpet assembly (A) into harness clip,
always check that floor carpet assembly is hooked to harness
clip normally. Otherwise, carpet may be misaligned after instal-
lation when it is stepped on.
: Pawl
JMJIA4396ZZ
B
: Harness
JMJIA6569ZZ
INT-26
< REMOVAL AND INSTALLATION >
HEADLINING
HEADLINING
NORMAL ROOF
NORMAL ROOF : Exploded View
INFOID:0000000009720372
NORMAL ROOF : Removal and Installation
INFOID:0000000009720373
REMOVAL
1.
Remove luggage side upper finisher (LH and RH). Refer to
INT-35, "Removal and Installation"
.
2.
Remove front pillar garnish (LH and RH) and center pillar upper garnish (LH and RH). Refer to
1.
Headlining assembly (with auto back
door)
2.
Assist grip cap
3.
Assist grip
4.
Sun-visor holder
5.
Sun-visor assembly
6.
Sun-visor cover
7.
Dual-lock fastener
8.
Auto back door finisher
9.
Auto back door plate
10. Rear center seat belt cover
11.
Map lamp assembly
12. Headlining assembly (without auto
back door)
: Clip
: Pawl
: Metal clip
JMJIA6883ZZ
HEADLINING
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3.
Disconnect roof harness (1) connectors (A), the antenna feeder (2) harness connector (C) and the clips
(B).
4.
Remove all assist grips.
a.
Disengage pawl of assist grip clip (1) using a remover tool (A).
Slide assist grip clip forward and remove it.
b.
Slide assist grip (2) forward and remove it.
5.
Remove sun-visor assembly (LH and RH).
a.
Disengage sun-visor cover fixing pawls using a remover tool (A),
and then remove sun-visor cover.
b.
Remove sun-visor assembly fixing screws.
c.
Disconnect harness connector, and then remove sun-visor assembly.
6.
Disconnect inside mirror and rain sensor harness connector.
• with ADP: Refer to
.
• without ADP: Refer to
L: Left side of vehicle
R: Right side of vehicle
: Clip
JMJIA2760ZZ
: Pawl
JMJIA4398ZZ
: Pawl
JMJIA4910ZZ
INT-28
< REMOVAL AND INSTALLATION >
HEADLINING
7.
Rotate 90
°
degrees and remove sun-visor holder (1) (LH and
RH).
8.
Recline front seat back to facilitate the headlining removal.
9.
Pull the map lamp assembly toward and disengage clip and
metal clips.
CAUTION:
Map lamp assembly is crimped from the back of headlining.
Remove it by disengaging the crimped area of back of map
lamp assembly after removing headlining from the vehicle.
10. Disengage rear center seat belt cover (1) fixing clips and metal
clip using a remover tool (A), then remove rear center seat belt
cover (1).
11. Disconnect the antenna feeder harness connectors (A), (B), and
clips.
12. Using remover tool, remove headlining hidden clip at the back side of headlining.
13. Peel dual-lock fastener.
JMJIA0098GB
: Clip
: Metal clip
JMJIA6885ZZ
: Clip
: Metal clip
JMJIA1009ZZ
: Clip
JMJIA6279ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст