Nissan Murano. Instruction — part 802
HA-44
< REMOVAL AND INSTALLATION >
LOW-PRESSURE PIPE
LOW-PRESSURE PIPE
Exploded View
INFOID:0000000009718646
HA-14, "Refrigerant Connection"
.
Removal and Installation
INFOID:0000000009718647
REMOVAL
1.
Use refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove mounting bolt (A) and then disconnect low-pressure
pipe (1) from expansion valve.
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve
with suitable material such as vinyl tape to avoid the entry
of air.
1.
High-pressure pipe
2.
O-ring
3.
Condenser assembly
4.
High-pressure flexible hose
5.
Compressor
6.
Low-pressure flexible hose
7.
Low-pressure pipe
8.
Heater & cooling unit assembly
9.
Evaporator pipe assembly
10. Expansion valve
11.
Evaporator
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JPIIA1257GB
JPIIA0536ZZ
LOW-PRESSURE PIPE
HA-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
3.
Remove mounting bolt (A) and then disconnect low-pressure
flexible hose (1) from low-pressure pipe (2).
CAUTION:
Cap or wrap the joint of the A/C piping with suitable mate-
rial such as vinyl tape to avoid the entry of air.
4.
Move power steering reservoir tank to a position where it dose not inhibit work. Refer to
(WITH HEATED STEERING WHEEL) or
(WITHOUT HEATED STEER-
ING WHEEL).
5.
Remove mounting nut (A) and clip (B), and then remove low-
pressure pipe (1) together with the low-pressure pipe bracket
(2).
INSTALLATION
Note the following items and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
JPIIA0533ZZ
JPIIA0537ZZ
HA-46
< REMOVAL AND INSTALLATION >
HIGH-PRESSURE PIPE
HIGH-PRESSURE PIPE
Exploded View
INFOID:0000000009718648
HA-14, "Refrigerant Connection"
.
Removal and Installation
INFOID:0000000009718649
REMOVAL
1.
Use refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove mounting bolt (A) and then disconnect high-pressure
pipe (1) from expansion valve.
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve
with suitable material such as vinyl tape to avoid the entry
of air.
1.
High-pressure pipe
2.
O-ring
3.
Condenser assembly
4.
High-pressure flexible hose
5.
Compressor
6.
Low-pressure flexible hose
7.
Low-pressure pipe
8.
Heater & cooling unit assembly
9.
Evaporator pipe assembly
10. Expansion valve
11.
Evaporator
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JPIIA1257GB
JPIIA0538ZZ
HIGH-PRESSURE PIPE
HA-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
3.
Remove mounting bolt (A) and then disconnect high-pressure
pipe (1) from condenser pipe assembly (2).
CAUTION:
Cap or wrap the joint of the A/C piping with suitable mate-
rial such as vinyl tape to avoid the entry of air.
4.
Move power steering reservoir tank to a position where it dose not inhibit work. Refer to
(WITH HEATED STEERING WHEEL) or
(WITHOUT HEATED STEER-
ING WHEEL).
5.
Remove reservoir tank. Refer to
.
6.
Remove washer tank inlet. Refer to
7.
Remove fixing clip (A), and then remove high-pressure pipe (1).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
JPIIA0539ZZ
JPIIA0540ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст