Nissan Murano. Instruction — part 803
HA-48
< REMOVAL AND INSTALLATION >
CONDENSER PIPE ASSEMBLY
CONDENSER PIPE ASSEMBLY
Exploded View
INFOID:0000000009718650
Removal and Installation
INFOID:0000000009718651
REMOVAL
1.
Use refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove front grille. Refer to
.
3.
Remove mounting bolt (A) and then disconnect high-pressure
flexible hose (2) and high-pressure pipe (3) from condenser pipe
assembly (1).
CAUTION:
Cap or wrap the joint of the A/C piping with suitable mate-
rial such as vinyl tape to avoid the entry of air.
1.
Condenser pipe assembly
2.
O-ring
3.
Condenser assembly
4.
Condenser lower bracket LH
5.
Bracket
6.
Liquid tank
7.
Refrigerant pressure sensor
8.
Liquid tank bracket
9.
Condenser upper bracket LH
10. Condenser upper bracket RH
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPIIA0460GB
JPIIA0541ZZ
CONDENSER PIPE ASSEMBLY
HA-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
4.
Remove mounting bolt (A) and then remove condenser pipe
assembly (1) from condenser.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser with
suitable material such as vinyl tape to avoid the entry of air.
INSTALLATION
Note the following items and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
JPIIA0542ZZ
HA-50
< REMOVAL AND INSTALLATION >
CONDENSER
CONDENSER
Exploded View
INFOID:0000000009718652
Removal and Installation
INFOID:0000000009718653
REMOVAL
1.
Remove condenser pipe assembly. Refer to
2.
Remove air guide upper and air guide center. Refer to
.
3.
Remove hood lock assembly. Refer to
4.
Disengage the joints of the pawl (A) and then move air guide
side LH (1) to the position without the hindrance for work.
1.
Condenser pipe assembly
2.
O-ring
3.
Condenser assembly
4.
Condenser lower bracket LH
5.
Bracket
6.
Liquid tank
7.
Refrigerant pressure sensor
8.
Liquid tank bracket
9.
Condenser upper bracket LH
10. Condenser upper bracket RH
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPIIA0460GB
JPIIA1348ZZ
CONDENSER
HA-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
5.
Disconnect refrigerant pressure sensor connector (A).
6.
Remove tabs (A). Pull the condenser (1) in the direction shown
by the arrow, and then remove it.
CAUTION:
Be careful not to damage core surface of condenser.
INSTALLATION
Note the following items and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
JPIIA0543ZZ
JPIIA1349ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст