Nissan Murano. Instruction — part 1408
TM-174
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
DIFFERENTIAL SIDE OIL SEAL
DIFFERENTIAL SIDE OIL SEAL
2WD
2WD : Exploded View
INFOID:0000000009719587
2WD : Removal and Installation
INFOID:0000000009719588
REMOVAL
1.
Remove front drive shafts. Refer to
.
2.
Remove differential side oil seals (1) using a flat-bladed screw-
driver (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal evenly using a commercial ser-
vice tool so that differential side oil seal protrudes by the dimension
(C) respectively.
Unit: mm (in)
NOTE:
Differential side oil seal pulling direction is used as the reference.
1.
RH differential side oil seal
2.
LH differential side oil seal
3.
Transaxle assembly
: Apply CVT fluid.
Refer to
for symbols not described above.
JPDIA0593ZZ
JPDIA0118ZZ
A
: Transaxle case side
B
: Converter housing side
Dimension C
0
±
0.5 (0
±
0.020)
JPDIA0618ZZ
DIFFERENTIAL SIDE OIL SEAL
TM-175
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CAUTION:
• Never reuse differential side oil seals.
• Apply CVT fluid to differential side oil seals.
Drift to be used:
2WD : Inspection
INFOID:0000000009719589
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
AWD
AWD : Exploded View
INFOID:0000000009719590
AWD : Removal and Installation
INFOID:0000000009719591
REMOVAL
1.
Remove exhaust front tube. Refer to
2.
Separate propeller shaft. Refer to
3.
Remove front drive shafts. Refer to
.
4.
Remove transfer from transaxle assembly. Refer to
Location
Tool number (Kent-Moore No.)
Transaxle case side
ST33400001 (J-26082)
Converter housing side
1.
Side oil seal (transfer joint)
2.
LH differential side oil seal
3.
Transaxle assembly
: Apply CVT fluid.
Refer to
for symbols not described above.
JPDIA0594ZZ
TM-176
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
DIFFERENTIAL SIDE OIL SEAL
5.
Remove differential side oil seal (1) and side oil seal (transfer
joint) using a flat-bladed screwdriver (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal and side oil seal (transfer joint)
evenly using a commercial service tool so that differential side oil
seal and side oil seal (transfer joint) protrudes by the dimension
(C) respectively.
Unit: mm (in)
NOTE:
Differential side oil seal and side oil seal (transfer joint) pulling direc-
tion is used as the reference.
CAUTION:
• Never reuse differential side oil seals and side oil seal (transfer joint).
• Apply CVT fluid to differential side oil seals and side oil seal (transfer joint).
Drift to be used:
AWD : Inspection
INFOID:0000000009719592
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
JPDIA0118ZZ
A
: Transaxle case side
B
: Converter housing side
Dimension C
0
±
0.5 (0
±
0.020)
JPDIA0619ZZ
Location
Tool number (Kent-Moore No.)
Differential side oil seal
ST33400001 (J-26082)
Side oil seal (transfer joint)
KV40100621 (J-25405)
AIR BREATHER HOSE
TM-177
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Exploded View
INFOID:0000000009719593
Removal and Installation
INFOID:0000000009719594
REMOVAL
1.
Remove air duct (inlet). Refer to
2.
Remove air cleaner case. Refer to
.
3.
Remove air breather hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Check that air breather hose is not collapsed or blocked due to folding or bending when installed.
• Install air breather hose to air breather tube so that the paint mark
(A) faces upward. Also insert hose to the bend of air breather tube.
1.
Air cleaner case
2.
Air breather hose
3.
Transaxle assembly
4.
Heater pipe
: Vehicle front
JPDIA0592ZZ
SCIA7584J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст