Nissan Murano. Instruction — part 1407
TM-170
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
CONTROL CABLE
10. Remove the control cable (1) from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
When installing control cable (1) to CVT shift selector assembly (2),
check that control cable is fully pressed in with the ribbed (A) surface
facing upward.
Inspection and Adjustment
INFOID:0000000009719580
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing control cable. Refer to
TM-164, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLATION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-164, "Inspection and Adjustment"
A
: Dash trim
: Bolt
JPDIA0629ZZ
JPDIA0609ZZ
OIL PAN
TM-171
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000009719581
Removal and Installation
INFOID:0000000009719582
REMOVAL
1.
Remove engine under cover with power tool.
2.
Remove drain plug.
3.
Remove O-ring from drain plug.
4.
Remove oil pan fitting bolts (
).
5.
Remove oil pan.
1.
Transaxle assembly
2.
Oil pan fitting bolt
3.
Drain plug
4.
O-ring
5.
Oil pan
6.
Oil pan gasket
7.
Magnet
: Apply CVT Fluid NS-2.
Refer to
JPDIA0608GB
: Vehicle front
SCIA8135J
TM-172
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
OIL PAN
6.
Remove oil pan gasket (1) from oil pan (2).
7.
Remove magnet (3) from oil pan.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mounting surface of
transaxle case and oil pan.
• Never reuse oil pan gasket, O-ring and oil pan fitting bolts.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000009719583
Check foreign materials in oil pan to help determine causes of malfunction. If the CVT fluid is very dark, smells
burned, or contains foreign particles, frictional material (clutches) may need replacement. A tacky film that will
not wipe clean indicates varnish build up. Varnish can cause valves and clutches to stick and can inhibit pump
pressure.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
SCIA8219J
SECONDARY SPEED SENSOR
TM-173
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SECONDARY SPEED SENSOR
Exploded View
INFOID:0000000009719584
Removal and Installation
INFOID:0000000009719585
REMOVAL
1.
Disconnect the battery cable from negative terminal.
2.
Remove air duct (inlet). Refer to
3.
Remove air cleaner case. Refer to
4.
Disconnect secondary speed sensor connector.
5.
Remove secondary speed sensor (1) and shim (2).
CAUTION:
Never lose the shim.
6.
Remove O-ring (3) from secondary speed sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000009719586
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
1.
Secondary speed sensor
2.
Shim
3.
Transaxle assembly
4.
O-ring
: Apply CVT fluid.
Refer to
for symbols not described above.
JPDIA0687GB
JPDIA0617ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст