Nissan Murano. Instruction — part 434
REAR DOOR LOCK
DLK-347
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
While pulling outside handle, remove outside handle escutch-
eon.
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7.
Remove front gasket and rear gasket.
8.
While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
9.
Reach in to separate outside handle cable connection on outside handle bracket.
10. Disconnect harness connector from door lock actuator.
11. Remove door lock mounting bolts.
12. Remove door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
JMKIA0560ZZ
JMKIA0524ZZ
PIIB5814E
DLK-348
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
INSIDE HANDLE : Exploded View
INFOID:0000000009719265
INSIDE HANDLE : Removal and Installation
INFOID:0000000009719266
REMOVAL
1.
Remove rear door finisher. Refer to
INT-17, "REAR DOOR FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting screws.
3.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
1.
TORX bolt
2.
Door lock assembly
3.
Inside handle cap
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Outside handle escutcheon
8.
Rear gasket
9.
Outside handle bracket
: Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
JMKIA1803GB
REAR DOOR LOCK
DLK-349
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE HANDLE : Exploded View
INFOID:0000000009719267
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009719268
REMOVAL
1.
Remove rear door finisher. Refer to
INT-17, "REAR DOOR FINISHER : Removal and Installation"
2.
Fully close rear door glass.
3.
Remove sealing screen. Refer to
GW-25, "Removal and Installation"
4.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
1.
TORX bolt
2.
Door lock assembly
3.
Inside handle cap
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Outside handle escutcheon
8.
Rear gasket
9.
Outside handle bracket
: Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
Refer to
for symbols in the figure.
JMKIA1803GB
JMKIA1467ZZ
DLK-350
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
5.
While pulling outside handle, remove outside handle escutch-
eon.
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7.
Remove front gasket and rear gasket.
8.
While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
9.
Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
JMKIA0560ZZ
JMKIA0524ZZ
PIIB5814E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст