Nissan Murano. Instruction — part 432
HOOD LOCK
DLK-339
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8.
Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never to damage (peeling) the outside of hood lock control cable.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never to bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark) properly.
• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to
DLK-309, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000009719256
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] by hood
weight.
2.
While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
3.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
4.
Install so that static closing face of hood is 94 – 490 N·m (9.6 – 50.0 kg-m, 69 – 361 ft – lb).
NOTE:
• Exert vertical force on right side and left side of hood lock.
• Never press simultaneously both sides.
5.
Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.
PIIB5801E
DLK-340
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000009719257
DOOR LOCK : Removal and Installation
INFOID:0000000009719258
REMOVAL
1.
Remove front door finisher. Refer to
INT-13, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove front door glass. Refer to
GW-19, "Removal and Installation"
3.
Remove front door module assembly. Refer to
GW-22, "Removal and Installation"
.
4.
Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.
1.
TORX bolt
2.
Key rod
3.
Door lock assembly
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
8.
Rear gasket
9.
Outside handle bracket
:Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
JMKIA1802GB
FRONT DOOR LOCK
DLK-341
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
CAUTION:
Never forcibly remove TORX bolt.
6.
Reach in to separate door key rod connection (on the handle)
(driver side).
7.
While pulling outside handle, remove door key cylinder assem-
bly (driver side) or outside handle escutcheon (passenger side).
8.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9.
Remove front gasket and rear gasket.
JMKIA0020ZZ
1.
Door key cylinder assembly
2.
Key rod
JMKIA0553ZZ
JMKIA0560ZZ
JMKIA0524ZZ
DLK-342
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
10. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
11. Reach in to separate outside handle cable connection on outside handle bracket.
12. Remove door lock assembly TORX bolts.
13. Disconnect door lock actuator connector, and then remove door lock assembly.
14. Remove key rod from door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• To install each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
INSIDE HANDLE : Exploded View
INFOID:0000000009719259
PIIB5814E
1.
TORX bolt
2.
Key rod
3.
Door lock assembly
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
8.
Rear gasket
9.
Outside handle bracket
JMKIA1802GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст