Nissan Murano. Instruction — part 430
BACK DOOR
DLK-331
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Remove back door hinge cover. Refer to
INT-38, "Removal and Installation"
2.
Loosen back door hinge mounting bolts (back door side).
3.
Loosen bumper rubber.
4.
Remove luggage rear plate mask. Refer to
INT-35, "Removal and Installation"
5.
Loosen back door striker mounting bolts.
6.
Lift up back door approximately 100 – 150 mm (3.937 – 5.906 in) height then close it lightly and check that
it is engaged firmly with back door closed.
7.
Check the clearance and surface height.
8.
Finally tighten back door hinge, bumper rubber, and back door striker.
9.
Install back door hinge cover and luggage rear plate mask. Refer to
INT-38, "Removal and Installation"
INT-35, "Removal and Installation"
.
CAUTION:
Adjust the following parts.
• Rear view camera.
- BASE AUDIO WITH COLOR DISPLAY: Refer to
.
- BOSE AUDIO WITHOUT NAVIGATION: Refer to
.
- BOSE AUDIO WITH NAVIGATION: Refer to
AV-466, "Adjustment (Models without BSW and LDW)"
.
BACK DOOR STRIKER ADJUSTMENT
Adjust back door striker so that becomes parallel with back door lock insertion direction.
BACK DOOR STRIKER
Back door – Rear fender
B – B
H
Clearance
4.0 – 8.0 (0.157 – 0.315)
—
I
Surface height
-2.0 – 2.0 (-0.079 – 0.079)
—
Back door – Rear combination
lamp
C – C
J
Clearance
4.0 – 8.0 (0.157 – 0.315)
< 2.0 (0.079)
Back door – Rear bumper fascia
D – D
K
Clearance
4.0 – 8.0 (0.157 – 0.315)
< 2.0 (0.079)
E – E
L
Clearance
5.0 – 9.0 (0.197 – 0.354)
—
Portion
Standard
Difference
(RH/LH)
DLK-332
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR STRIKER : Exploded View
INFOID:0000000009719245
BACK DOOR STRIKER : Removal and Installation
INFOID:0000000009719246
REMOVAL
1.
Remove luggage rear plate. Refer to
INT-35, "Removal and Installation"
2.
Remove mounting bolts, and then remove back door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check back door open/close operation after installation.
• When removing and installing back door striker, be sure to perform the fitting adjustment. Refer to
DLK-330, "BACK DOOR ASSEMBLY : Adjustment"
BACK DOOR HINGE
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
BACK DOOR
DLK-333
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR HINGE : Exploded View
INFOID:0000000009719247
BACK DOOR HINGE : Removal and Installation
INFOID:0000000009719248
REMOVAL
1.
Remove back door assembly. Refer to
DLK-328, "BACK DOOR ASSEMBLY : Removal and Installation"
2.
Remove luggage side finisher lower and luggage side finisher upper. Refer to
.
3.
Using a remover tool, remove headlining clip at the rear side of headlining. Refer to
INT-30, "SUNROOF : Exploded View"
(SUNROOF).
4.
Remove rear side of headlining.
5.
Remove power back door drive assembly. Refer to
DLK-352, "POWER BACK DOOR DRIVE ASSEMBLY
6.
Remove back door hinge mounting nuts (body side), and then remove back door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check back door open/close operation after installation.
• Check back door hinge rotating part for poor lubrication. If necessary, apply body grease.
• When removing and installing back door assembly, perform the fitting adjustment. Refer to
"BACK DOOR ASSEMBLY : Adjustment"
.
• After installation, apply touch-up paint (the body color) onto the head of back door hinge mounting
nuts.
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
DLK-334
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR STAY
BACK DOOR STAY : Exploded View
INFOID:0000000009719249
BACK DOOR STAY : Removal and Installation
INFOID:0000000009719250
REMOVAL
1.
Support back door assembly with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding back door open when removing back door
stay.
2.
Remove mounting bolts of back door stay (body side).
3.
Remove metal clip (3) located on the connection between the
back door stay (1) and the stud ball (2) (back door side), by
using a flat-bladed screwdriver (A).
4.
Disengage and remove back door stay from stud ball (back door
side).
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
JMKIA2255ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст