Nissan Murano. Instruction — part 431
BACK DOOR
DLK-335
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check back door open/close operation after installation.
BACK DOOR STAY : Disposal
INFOID:0000000009719251
1.
Fix back door stay (1) using a vise (C).
2.
Using hacksaw (A) slowly make 2 holes in the back door stay, in
numerical order as shown in the figure.
CAUTION:
• When cutting a hole on back door stay, always cover a
hacksaw using a shop cloth (B) to avoid scattering metal
fragments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
BACK DOOR WEATHER-STRIP
JMKIA3336ZZ
A:
20 mm (0.787 in)
B:
Cut at the groove.
JMKIA3609ZZ
DLK-336
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
BACK DOOR WEATHER-STRIP : Exploded View
INFOID:0000000009719252
BACK DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000009719253
REMOVAL
1.
Remove mounting bolts of power back door drive assembly (1)
(back door side).
2.
Pull up and remove engagement with body from weather-strip joint.
CAUTION:
Never pull strongly on weather-strip.
INSTALLATION
1.
Working from the upper section, align weather-strip center mark (A) with vehicle center mark (cutting posi-
tion) and install weather-strip onto the vehicle.
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
JMKIA1918ZZ
BACK DOOR
DLK-337
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
For the lower section, align weather-strip seam with center of back door striker.
3.
Pull weather-strip gently to ensure that there is no loose section.
NOTE:
Make sure that weather-strip is fit tightly at each corner and luggage rear plate.
4.
Install mounting bolts of power back door drive assembly (back door side).
DLK-338
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD LOCK
HOOD LOCK
Exploded View
INFOID:0000000009719254
Removal and Installation
INFOID:0000000009719255
REMOVAL
CAUTION:
Check wiring of hood lock control before removal.
1.
Remove front grille. Refer to
EXT-21, "Removal and Installation"
2.
Remove mounting bolts, and then remove hood lock assembly
(1).
NOTE:
Press the lever downward to avoid pin (A), then pull out hood
lock assembly upward.
3.
Disconnect hood lock cable (2) from hood lock assembly.
4.
Remove instrument lower panel (LH). Refer to
IP-15, "Removal and Installation"
5.
Disconnect hood lock cable from instrument lower panel (LH).
6.
Remove fender protector (LH). Refer to
EXT-26, "FENDER PROTECTOR : Removal and Installation"
7.
Remove hood lock cable clamp.
1.
Hood lock assembly
2.
Hood lock control cable
3.
Hood lock opener
: Clip
Refer to
for symbols in the figure.
JMKIA1798ZZ
JMKIA1914ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст