Nissan Murano. Instruction — part 464
PREPARATION
DLN-95
< PREPARATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Commercial Service Tools
INFOID:0000000009718178
ST3127S000
(J-25765-A)
Preload gauge
Measuring preload torque
KV381086S1
(
—
)
Dummy cover set
1. KV38108610
(
—
)
Dummy cover
2. KV38108621
(
—
)
Dummy cover spacer
3. KV38108630
(
—
)
Dummy cover shim
• Checking backlash
• Checking drive gear runout
• Checking tooth contact
Tool number
(Kent-More No.)
Tool name
Description
ZZA0503D
SDIA2313E
Tool name
Description
Flange wrench
Removing and installing companion flange
lock nut
Power tool
Loosening bolts and nuts
NT771
PBIC0190E
DLN-96
< PERIODIC MAINTENANCE >
[REAR FINAL DRIVE: R145]
REAR DIFFERENTIAL GEAR OIL
PERIODIC MAINTENANCE
REAR DIFFERENTIAL GEAR OIL
Inspection
INFOID:0000000009718179
OIL LEAKAGE
Check that oil is not leaking from final drive assembly or around it.
OIL LEVEL
• Remove filler plug (1) and check oil level from filler plug mounting
hole as shown in the figure.
CAUTION:
Never start engine while checking oil level.
• Set a new gasket on filler plug and install it on final drive assembly.
CAUTION:
Never reuse gasket.
Draining
INFOID:0000000009718180
1.
Stop engine.
2.
Remove drain plug (1) and drain gear oil.
3.
Set a new gasket on drain plug and install it to final drive assem-
bly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
Refilling
INFOID:0000000009718181
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.
2.
After refilling oil, check oil level. Set a new gasket to filler plug, then install it to final drive assembly. Refer
to
CAUTION:
Never reuse gasket.
JPDID0164ZZ
JPDID0163ZZ
Oil grade and viscosity
: Refer to
NORTH AMERICA : Fluids
and Lubricants"
(for
NORTH AMERICA),
"FOR MEXICO : Fluids and
Lubricants"
(for MEXICO).
Oil capacity
: Refer to
JPDID0164ZZ
FRONT OIL SEAL
DLN-97
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
FRONT OIL SEAL
Exploded View
INFOID:0000000009718182
Removal and Installation
INFOID:0000000009718183
REMOVAL
1.
Remove rear propeller shaft. Refer to
2.
Put matching mark on the thread edge of electric controlled cou-
pling. The matching mark should be in line with the matching
mark on companion flange.
CAUTION:
For matching mark, use paint. Never damage electric con-
trolled coupling.
1.
Final drive assembly
2.
Front oil seal
3.
Companion flange
4.
Companion flange lock nut
A.
Oil seal lip
: Vehicle front
: Apply gear oil.
Refer to
for symbols not described above.
JPDID0004GB
PDIA0455E
DLN-98
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
FRONT OIL SEAL
3.
Remove companion flange lock nut, using a flange wrench
(commercial service tool). Then remove companion flange.
4.
Remove front oil seal from coupling cover, using a suitable tool.
CAUTION:
Be careful not to damage coupling cover.
INSTALLATION
1.
Install front oil seal until it becomes flush with the coupling cover
end, using the drifts.
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lips, and gear oil
onto the circumference of oil seal.
2.
Align the matching mark of electric controlled coupling with the
matching mark of companion flange, then install the companion
flange.
3.
Install companion flange lock nut with a flange wrench (commer-
cial service tool), tighten to the specified torque.
CAUTION:
Never reuse companion flange lock nut.
4.
Install rear propeller shaft. Refer to
.
5.
When oil leaks while removing, check oil level after the installa-
tion. Refer to
JSDIA0199ZZ
JSDIA0200ZZ
A
: Drift [SST: KV38100200 (J-26233)]
B
: Drift [SST: ST27861000 (
—
)]
PDIA0038E
PDIA0455E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст