Nissan GT-R. Instruction — part 123
EXT-46
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
2.
Heat adhesive tape interface with a dryer, and then peel roof side molding clips with long-nose pliers.
CAUTION:
Be careful not to damage the body.
Installation
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5.
Tape clips after press fit, and temporarily hold it for specified time based on the following.
6.
Install from roof side molding rear end to front end in this order after temporarily holding.
CAUTION:
• When installing roof side molding of windshield portion, check that molding fastener is securely
inserted and then press in.
• Never wash the vehicle with in 24 hours so as to keep adhesive.
Adhesive
: 3M–weld DP-100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N
×
2 seconds
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
FRONT PILLAR FINISHER
EXT-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FRONT PILLAR FINISHER
Exploded View
INFOID:0000000009161577
Removal and Installation
INFOID:0000000009161578
REMOVAL
1.
Remove the mounting clips and the double-faced adhesive tape of the body side weather-strip.
2.
Remove the body side weather-strip.
NOTE:
Disengage the joint of front pillar clip while sliding upward.
3.
Remove the mounting screws (A) and the clip (B), and then
remove the weather-strip retainer (1).
1.
Front pillar finisher
2.
Weather-strip retainer
3.
Body side weather-strip
4.
Grommet
: Clip
Refer to
NNKIA0150ZZ
NNKIA0151ZZ
EXT-48
< REMOVAL AND INSTALLATION >
FRONT PILLAR FINISHER
4.
Insert the remover tool (A) from the rear edge of the front pillar
finisher (1), and then disengage the clips toward vehicle front.
CAUTION:
Apply protective tape (B) to the body side to protect from
damage.
5.
Remove the front door finisher from the vehicle body.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• During installation check that the clips are aligned with the vehicle body side panel holes, and then
press.
• Never reuse the body side weather-strip.
• To maintain adhesion, never wash the vehicle within 24 hours after installing the body side weather-
strip.
: Clip
NNKIA1738ZZ
DOOR OUTSIDE MOLDING
EXT-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
DOOR OUTSIDE MOLDING
Exploded View
INFOID:0000000009161579
Removal and Installation
INFOID:0000000009161580
REMOVAL
1.
Fully open the door window.
2.
Twist the door outside molding (1) toward the outside of the
vehicle, and then lift up and remove it while disengaging the
pawls.
INSTALLATION
Install in the reverse order of removal.
1.
Door outside molding
2.
Door panel assembly
Refer to
for symbols in the figure.
NNKIA0153ZZ
JMKIA0116GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст