Nissan GT-R. Instruction — part 124
EXT-50
< REMOVAL AND INSTALLATION >
DOOR PARTING SEAL
DOOR PARTING SEAL
Exploded View
INFOID:0000000009161581
Removal and Installation
INFOID:0000000009161582
REMOVAL
1.
Fully open the door.
2.
Remove the clips (parting seal clip) of door parting seal (1) with
the remover tool (A).
CAUTION:
Be careful no to damage the body.
3.
Remove the door parting seal from the door assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Door assembly
2.
Door parting seal
3.
Parting seal clip
4.
Double-faced adhesive tape
[t: 2.0mm (0.079in)]
Refer to
for symbols in the figure.
NNKIA1704ZZ
: Clip
NNKIA0155ZZ
DOOR PARTING SEAL
EXT-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
CAUTION:
Visually check the clips for deformation and damage at installation. Replace with new ones if neces-
sary.
EXT-52
< REMOVAL AND INSTALLATION >
REAR WING
REAR WING
Exploded View
INFOID:0000000009161583
Removal and Installation
INFOID:0000000009161584
REMOVAL
1.
Remove the trunk lid finisher inner. Refer to
INT-29, "Removal and Installation"
.
1.
Rear wing assembly
2.
Grommet
3.
Rear wing clip
4.
Center leg bracket
5.
High-mounted stop lamp
6.
Double-faced adhesive tape
[t: 1.6 mm (0.063 in)]
7.
EPT sealer
Refer to
for symbols in the figure.
NNKIA1705ZZ
REAR WING
EXT-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2.
Disconnect the harness connector of trunk lid lock assembly (1)
and the harness connectors (A) of high-mounted stop lamp.
3.
Remove the mounting nuts (A) of rear wing assembly.
4.
Apply protective tape (A) around the outer edge of mating sur-
face between rear wing assembly and trunk lid to prevent from
damage.
5.
Disengage the clips with the remover tool while peeling the double-faced adhesive tape with threads.
CAUTION:
Never bore the rear wing assembly with excessive power. It may cause cracks in the paint.
6.
Replace the following parts after removing the rear wing assembly.
• High-mounted stop lamp: Refer to
EXL-59, "Removal and Installation"
• Clip and grommet for rear wing assembly
• EPT sealer
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never disassemble the rear wing assembly.
• Replace the double-faced adhesive tape of the back surface with new tape when reusing the rear
wing assembly.
- Remove the double-faced adhesive tape remaining on the rear wing assembly with a double-faced
adhesive tape remover.
- Remove any double-faced adhesive tape remaining on the vehicle side in a similar manner, and then
apply the primer for painted surfaces (Nissan parts dealer).
- Heat the rear wing assembly application surface and panel surface to 20
°
C (68
°
F) or more.
- Press-fit the entire area of the double-faced adhesive tape with 5 kg/cm
2
or more of pressure after
applying the rear wing assembly on the vehicle body.
• Replace the EPT sealer of the back surface with new sealer when reusing the rear wing assembly.
Remove the EPT sealer remaining on the rear wing assembly using a double-faced adhesive tape
remover.
NNKIA0161ZZ
NNKIA0158ZZ
NNKIA0157ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст