Nissan GT-R. Instruction — part 149
REAR WINDOW GLASS
GW-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR WINDOW GLASS
Exploded View (GT-R certified NISSAN dealer)
INFOID:0000000009161684
1.
Rear window glass
2.
Dam rubber
3.
Spacer
4.
Roof panel
5.
Primer
6.
Adhesive
7.
Body side outer panel
8.
Rear waist
9.
Headlining
10. Rear pillar finisher
11.
Rear pillar inner
12. Trunk lid outer
13. Trunk lid weather-strip
14. Rear parcel shelf finisher
15. Mark
16. Black print
Unit: mm (in)
NNKIA0003GB
GW-20
< REMOVAL AND INSTALLATION >
REAR WINDOW GLASS
for the symbols shown in the figure.
Removal and Installation (GT-R certified NISSAN dealer)
INFOID:0000000009161685
REMOVAL
1.
Remove rear pillar finisher (LH/RH). Refer to
INT-15, "Removal and Installation"
2.
Remove partially headlining (rear edge). Refer to
INT-24, "Removal and Installation"
.
3.
Remove rear parcel shelf finisher. Refer to
INT-19, "Removal and Installation"
4.
Remove connectors and grounds for rear window defogger and printed antenna.
5.
Apply protective tape around rear window glass to prevent painted surface from being damaged.
6.
If rear window glass will be reused, paint matching marks on the
body and glass.
NOTE:
Positioning during installation can be easily performed. Mount
the glass on the body and put the matching marks after clearing
the body side especially when installing new glass.
7.
Cut the adhesive.
Use a windshield cutter for straight section. For the area that the windshield cutter cannot be used, use
piano wire or a cutter knife.
a.
With a windshield cutter
i.
Apply soapy water around the bonded area on the body for
smooth movement of the windshield cutter (A).
ii.
Insert windshield knife into the bonded area from the passenger
room side. Cut adhesive by pulling the knife, keeping the tip par-
allel to the edge of the glass.
b.
With piano wire
For the area that the windshield cutter cannot be used, use piano wire.
i.
From the area cut by the windshield cutter, pass the piano wire through the passenger room side and tie
both sides to wire grips.
ii.
Cut the adhesive by alternately pulling the piano wire along with the glass.
CAUTION:
• Never press the piano wire excessively against the edge of the glass.
• Always use a Standish cover (stainless plate) to keep the piano wire clear of plastic parts.
c.
With a cutter knife
i.
Working from inside cabin, insert a cutter knife between rear window glass and body side outer panel.
Work the cutter knife along the edge of the rear window glass to cut off the adhesive.
CAUTION:
Never contact painted surfaces with the cutter knife tip.
PIIB3503J
JMKIA0306ZZ
REAR WINDOW GLASS
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
8.
Use rubber suction cups or suction lifter (A), etc. to remove
glass from the vehicle.
INSTALLATION
1.
Using a scraper, remove remaining adhesive (sealant) on the
body side down to approximately a depth that is 2.0 mm (0.079
in) thick (a) so that entire contour becomes smooth.
CAUTION:
If the bonded area on the body is scratched, repair it with a
two-liquid type urethane paint. Never use lacquer type
paint.
2.
When reusing the glass (2), use the cutter (A) to remove the
remaining adhesive (1) (sealant) and smooth out the surface.
3.
Mount the glass onto the vehicle and paint matching marks on the body and glass when installing new
glass. Then remove the glass again.
4.
Use the rubber suction cups or suction lifter (A) to set the glass
(1) on the glass stand (B).
5.
Clean the bonded area on the glass and body with white gasoline or degreasing agent.
6.
Install new spacer.
7.
Apply primer for the glass along the entire circumference of the glass.
Use the sealing kit for glass application and the special holder for cartridge or similar tools.
CAUTION:
There are 2 types of primer. Never confuse the application methods.
• Primer for painted surfaces
JMKIA1138ZZ
JMKIA0307ZZ
JMKIA0726ZZ
JMKIA1137ZZ
GW-22
< REMOVAL AND INSTALLATION >
REAR WINDOW GLASS
• Primer for glass
NOTE:
The essential function of primers is to strengthen adhesion between glass and painted surface.
8.
Apply primer for the painted surface to the body side bonding surface.
CAUTION:
• If the body side bonding surface is repaired with a two-liquid type urethane paint, always apply
the primer after drying the paint.
• If primer for painted surfaces adheres to a painted surface other than the bonding area, or if it
overflows, quickly remove it with white gasoline or degreasing agent.
9.
Affix the dam rubber and apply adhesive along the edge of the glass within the time period indicated in the
instruction instruction after applying primer.
• When reusing the glass, affix new dam rubber at the same place where old dam rubber was affixed.
• When installing new glass, apply the dam rubber from the edge of the glass so as to hide the black print.
CAUTION:
Apply the dam rubber (1) to the outer edge of the outline
mark of black print as shown in Exploded View. Apply it so
as to only place it without pulling.
NOTE:
Open adhesive by cutting off the nozzle tip and set it in a sealant
gun.
10. Use rubber suction cups or suction lifter (A) that are installed in
advance, align the matching marks to install.
CAUTION:
2 or more workers are required when installing the glass.
11. Press the entire surface of the glass lightly to fit it completely.
12. Correct any adhesive overflow or shortage using a spatula to make the surface smooth.
CAUTION:
After installing glass, keep the front door glass open until the adhesive is completely cured. Avoid
driving the vehicle.
13. Remove the protective tape.
14. Install the removed parts.
CAUTION:
Check the mating area with surrounding parts. Adjust if necessary.
Inspection (GT-R certified NISSAN dealer)
INFOID:0000000009161686
WATER LEAKAGE INSPECTION
CAUTION:
Wait at least 2 hours after installing the glass because the adhesive must be cured before performing
the leakage test.
JMKIA0727ZZ
JMKIA1138ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст