Nissan GT-R. Instruction — part 116
EXT-18
< REMOVAL AND INSTALLATION >
FRONT BUMPER
• Grind the head of rivet (1) with a drill (A) [bit of
φ
4.0 – 4.5 mm
(
φ
0.157 – 0.177 in)], and then remove the bumper side
bracket.
• Securely crimp the bumper side bracket with the bumper fas-
cia using a hand riveter (B).
13. Remove the energy absorber.
14. Remove the mounting bolts (A) and (B), and then remove the
bumper brackets (1) (LH/RH).
15. Remove the mounting bolts, and then remove the bumper reinforcement with power tool.
INSTALLATION
Note the following, and install in the reverse order of removal.
If front bumper fascia is replaced with new one, install blind nut following the steps as below.
1.
Make a hole in the front bumper fascia with drill, shown in the figure.
Bumper side bracket
Crimping thickness
: 1.2 – 6.4 mm (0.047 – 0.252 in)
Prepared hole diameter
:
φ
4.1 –
φ
4.4 mm (0.161 – 0.173 in)
Used rivet head diameter :
φ
8.0 mm (0.315 in)
NNKIA0122ZZ
NNKIA1693ZZ
Dimension
A: Distance from vehicle center
: 88.9 mm (3.500 in)
B: Distance from edge
: 41.6 mm (1.638 in)
C: Hole size
:
φ
9.7 mm (0.382 in)
JMKIA2995ZZ
FRONT BUMPER
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2.
Insert blind nut (A) to hand nut rivet setter (B).
3.
Set blind nut with hand nut rivet setter (A).
CAUTION:
Tighten the bumper brackets (LH/RH) and the bumper reinforcement after installing the engine under-
cover because the structure is so designed not to have any dimensional fluctuation between bumper
reinforcement and engine under cover.
NOTE:
Clearance between front bumper and each unit.
JMKIA2996ZZ
JMKIA2997ZZ
JMKIA3006ZZ
Portion
Clearance
Surface height difference
Front bumper and hood
A – A 1.5 – 5.5 mm (0.059 – 0.217 in)
−
2.0 – 0.0 mm (
−
0.079 – 0.000 in)
Front bumper and head lamp
B – B 0.5 – 3.5 mm (0.020 – 0.138 in)
—
Front bumper and front fender C – C 0.0 – 0.8 mm (0.000 – 0.031 in)
−
0.2 – 1.8 mm (
−
0.008 – 0.071 in)
Front bumper and engine un-
dercover
D – D 0.0 – 1.0 mm (0.000 – 0.039 in)
−
1.0 – 1.0 mm (
−
0.039 – 0.039 in)
EXT-20
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded View
INFOID:0000000009161555
1.
Bumper fascia
2.
Energy absorber
3.
Bumper reinforcement
4.
Bumper stay RH
5.
Bumper side bracket B RH
6.
Bumper side bracket A RH
7.
Rear bumper upper frame RH
8.
Rear bumper upper frame LH
9.
Bumper side bracket A LH
JMKIA2775ZZ
REAR BUMPER
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000009161556
CAUTION:
• Be careful of being burned because the rear bumper guard is very hot after driving.
• The bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact
with oil.
REMOVAL
1.
Open trunk lid.
2.
Remove the trunk floor carpet, trunk rear finisher and rear wheel house finishers (LH/RH). Refer to
27, "Removal and Installation"
3.
Remove the mounting nuts (A) of rear combination lamps (1)
(LH/RH).
4.
Disconnect the harness connector (B) and remove the harness
grommet (C) from the rear combination lamps (LH/RH).
5.
Remove the mounting nuts (A) of the side marker lens (1) (LH/
RH).
6.
Remove the clips (A) from the lower surface of bumper fascia.
10. Bumper side bracket B LH
11.
Bumper stay LH
12. Rear emblem
13. Rear combination lamp RH
14. Rear combination lamp LH
15. Side marker lens LH
16. Rear bumper side frame B LH
17. Bumper side bracket C LH
18. Rear bumper guard LH
19. Bumper fascia (lower)
20. Bumper side bracket C RH
21. Rear bumper side frame B RH
22. Rear bumper side frame A RH
23. License lamp bracket
24. Rear bumper side frame A LH
25. Side marker lens RH
26. Bumper finisher
27. Rear bumper guard RH
28. J-nut
for symbols in the figure.
NNKIA0111ZZ
NNKIA0112ZZ
NNKIA0113ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст