Nissan Titan. Instruction — part 521
SE-50
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
4. Pull the middle part of the seatback board to disengage the side
tabs (B) from the seatback frame.
5. Pull the lower part of the seatback board to disengage the bot-
tom clips from the seatback frame.
Installation
Installation is in the reverse order of removal.
SEATBACK BOARD - HARD SEATBACK
Removal
1. The seatback board is attached to the seat frame with the follow-
ing:
• 2 top tabs (A)
• 2 side tabs (B)
• 2 bottom clips (C) (must be replaced)
2. Move seat to forward position.
3. Hold the seatback board as shown and pull the bottom of the
seatback board away from the seat back frame.
4. Pull the middle part of the seatback board to disengage the side
tabs (B) from the seatback frame.
5. Lift the upper part of the seatback board to disengage the top
tabs from the seatback frame.
Installation
Installation is in the reverse order of removal.
ALIIA0367ZZ
ALIIA0395ZZ
ALIIA0370ZZ
ALIIA0371ZZ
FRONT SEAT
SE-51
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
SEAT CUSHION TRIM AND PAD
CAUTION:
• Front passenger seat is equipped with Occupant Classification System sensor and control module.
Do not disassemble front passenger seat cushion assembly or remove trim as this will affect the
Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
• When removed, the passenger seat cushion must always be placed pan side UP to prevent damage.
• During installation, the wire harness clips must be installed in the holes they were originally in.
Do not add additional clips.
• The Occupant Classification System control module can only be replaced as part of the seat cushion
assembly.
NOTE:
If the vehicle has been involved in a collision the seat must be inspected for damage. Refer to
.
1. Remove the power seat switch knobs and power seat switch
escutcheon (or recline knobs on instruction seat).
2. Remove the front seat cushion finisher (inner).
3. Remove the power seat switch screws (or lift knobs on instruction seats).
4. Remove four bolts and the seat cushion assembly.
5. Remove the retainer on the seat cushion frame, then remove the harness connector for the seat heater.
6. On the drivers seat only, after removing the seat cushion trim and pad, remove the hog rings to separate
the trim cover from the pad and seat cushion heater unit.
LIIA0681E
LIIA0285E
SIIA0503E
SE-52
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR SEAT
REAR SEAT
Exploded View
INFOID:0000000009882020
LH
ALJIA1070ZZ
1.
Seatback pad
2.
Headrest
3.
Seatback latch
4.
Seatback latch release strap
5.
Seatback latch striker
6.
Seatback frame
REAR SEAT
SE-53
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
RH
7.
Outboard pivot cover
8.
Release lever handle
9.
Seat cushion frame
10. Seat cushion release assembly
11. Outboard seat support
12. Grocery bag hooks
13. Inboard seat support
14. Rear seat bracket
15. Seat cushion pad
16. Seat cushion trim
17. Seatback trim
18. Inboard outer pivot cover
19. Inner inboard pivot cover
20. Headrest holder (free)
21. Headrest holder (locked)
ALJIA1071ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст