Nissan Titan. Instruction — part 520
SE-46
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Power Passenger Seat
ALJIA1068ZZ
1.
Seat slide knob
2.
Seat recline knob
3.
Power seat switch finisher
4.
Power seat switch
5.
Seat cushion assembly
6.
Recline motor
7.
Bolt cover
8.
Seat cushion outer finisher (RH)
9.
Slide finisher (RH)
10. Seat slide motor
11. Seat cushion front finisher
12. Seat frame assembly
13. Seat cushion outer finisher (LH)
14. Seat harness
15. Rear slide finisher (LH)
16. Recline mechanism cover (LH)
17. Recline rod
18. Recline mechanism cover (RH)
FRONT SEAT
SE-47
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Instruction Passenger Seat
19. Armrest assembly (if equipped)
20. Armrest insert (if equipped)
21. Armrest pivot bolt finisher (if
equipped)
22. Armrest washer (if equipped)
23. Armrest pivot bolt (if equipped)
24. Seatback assembly
25. Headrest holder (free)
26. Seat fold lever
27. Headrest holder (locked)
28. Seatback board
29. Headrest
A.
Seatback board clip
ALJIA1069ZZ
SE-48
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Disassembly and Assembly
INFOID:0000000009882019
SEATBACK TRIM AND PAD
NOTE:
Only complete outboard seatback assemblies can be replaced on vehicles equipped with side air bags.
Be sure to set the front/rear cushion lifter to the top position.
1. Remove the seatback board.
2. Remove the retainer.
3. Remove the headrest.
4. From inside of the seatback, squeeze the headrest holder tabs
at the base of the stay pipe and pull the up to remove.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
5. Remove the snap ring and the lumbar support lever knob.
1.
Seat cushion assembly
2.
Bolt cover
3.
Recline lever
4.
Seat cushion outer finisher (RH)
5.
Slide finisher (RH)
6.
Slide release wire
7.
Front seat frame support
8.
Seat cushion outer finisher (LH)
9.
Rear slide finisher (LH)
10. Seat frame cover
11. Recline rod
12. Recline mechanism cover (LH)
13. Seat cushion assembly
14. Recline mechanism cover (RH)
15. Armrest washer (if equipped)
16. Armrest assembly (if equipped)
17. Armrest insert (if equipped)
18. Armrest pivot bolt finisher (if
equipped)
19. Armrest pivot bolt (if equipped)
20. Seatback assembly
21. Headrest holder (free)
22. Seat fold lever
23. Headrest holder (locked)
24. Seatback board
25. Headrest
A.
Seatback board clip
SIIA0113E
LRS023
PIIA1156E
FRONT SEAT
SE-49
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
6.
CAUTION:
On the passenger seat during installation, the wire harness clips must be installed in the holes
they were originally in.
Do not add additional clips.
Disconnect the seatback heater harness. Remove the seatback trim and pad assembly. Remove the hog
ring to separate the seatback trim from the pad and the heater unit.
Removal of seatback assembly
1. Remove the seatback board.
2. Remove the retainer.
3. Remove the side air bag harness connector from the seat cush-
ion.
4. Remove the seatback bolts (two for each side) and seatback
assembly.
Installation of seatback assembly
• Installation is in the reverse order of removal.
SEATBACK BOARD - SOFT SEATBACK
Removal
1. The seatback board is attached to the seat frame with the follow-
ing:
• 2 top tabs (A)
• 4 side tabs (B)
• 2 bottom clips (C) (must be replaced)
2. Move seat to forward position.
3. Hold the seatback board as shown and pull the top of the seat-
back board away from the seat back frame.
SIIA0113E
ALIIA0394ZZ
ALIIA0368ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст