Nissan Titan. Instruction — part 633
TRANSMISSION ASSEMBLY
TM-215
< UNIT REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8. Remove crankshaft position sensor (POS) from A/T assembly.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings or foreign material to get on the
sensor front edge magnetic area.
• Do not place in an area affected by magnetism.
9. Remove A/T fluid cooler tubes from A/T assembly.
CAUTION:
Do not reuse copper sealing washers.
10. Remove dust cover from converter housing.
11. Turn crankshaft to access and remove the four bolts for drive
plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
12. Support A/T assembly using transmission jack and Tool.
CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug.
13. Remove cross member using power tool.
14. Tilt the transmission slightly to keep the clearance between body and transmission, then disconnect air
breather hose. Refer to
TM-195, "4WD : Removal and Installation"
.
15. Remove air breather hose. Refer to
TM-195, "4WD : Removal and Installation"
.
16. Disconnect the following.
• Neutral 4 low switch
• Wait detection switch
• Transfer motor connector
• A/T assembly connector
• Transfer control device connector
• ATP switch connector
• Transfer terminal cord assembly connector
17. Remove A/T fluid indicator pipe.
CAUTION:
Do not reuse O-ring.
18. Remove A/T assembly to engine bolts using power tool.
19. Remove A/T assembly with transfer from vehicle.
CAUTION:
• Secure torque converter to prevent it from dropping.
• Secure A/T assembly to transmission jack.
20. Remove transfer from A/T assembly. Refer to
INSPECTION
LCIA0334E
LCIA0335E
Tool number
:
—
(J-47002)
SCIA2203E
TM-216
< UNIT REMOVAL AND INSTALLATION >
TRANSMISSION ASSEMBLY
Installation and Inspection of Torque Converter
• After inserting a torque converter to a transmission, be sure to
check distance (A) to ensure it is within specifications.
INSTALLATION
Installation is in the reverse order of removal, while paying attention to the following:
CAUTION:
Do not reuse O-ring and copper sealing washers.
• When installing transmission to the engine, attach the bolts as
shown.
CAUTION:
• When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.
• Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.
NOTE:
*: No.2 bolt also secures air breather tube.
• Align the positions of bolts for drive plate with those of the torque
converter, and temporarily tighten the bolts. Then tighten the bolts
with the specified torque. Refer to
TM-213, "Removal and Installa-
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
• After converter is installed to drive plate, rotate crankshaft
several turns and check to be sure that transmission rotates
freely without binding.
• Install crankshaft position sensor (POS).
• After completing installation, check fluid leakage, fluid level, and
the positions of A/T. Refer to
TM-172, "Checking the A/T Fluid (ATF)"
TM-190, "Inspection and Adjust-
.
Distance (A)
: 24.0 mm (0.94 in) or more
SAT017B
Transmission to engine bolts : 113 N·m (12 kg-m,
83 ft-lb)
LCIA0371E
LCIA0335E
OVERHAUL
TM-217
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
OVERHAUL
Component
INFOID:0000000009885925
WCIA0661E
TM-218
< UNIT DISASSEMBLY AND ASSEMBLY >
OVERHAUL
1.
O-ring
2.
Oil pump cover
3.
O-ring
4.
Oil pump housing
5.
Self-sealing bolts
6.
Torque converter
7.
Converter housing
8.
Oil pump housing oil seal
9.
Bearing race
10. Needle bearing
11. O-ring
12. Front carrier assembly
13. Needle bearing
14. Snap ring
15. Front sun gear
16. 3rd one-way clutch
17. Snap ring
18. Bearing race
19. Needle bearing
20. Seal ring
21. Input clutch assembly
22. Needle bearing
23. Rear internal gear
24. Brake band
25. Mid carrier assembly
26. Needle bearing
27. Bearing race
28. Rear carrier assembly
29. Needle bearing
30. Mid sun gear
31. Seal ring
32. Rear sun gear
33. 1st one-way clutch
34. Snap ring
35. Needle bearing
36. High and low reverse clutch hub
37. Snap ring
38. Bearing race
39. Needle bearing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст