Nissan Titan. Instruction — part 130
DLN-92
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
FRONT OIL SEAL
FRONT OIL SEAL
Removal and Installation
INFOID:0000000009886034
REMOVAL
1. Remove the front propeller shaft. Refer to
DLN-130, "Removal and Installation"
.
2. Remove the companion flange self-lock nut using suitable tool.
3. Put a matching mark on top of the front drive shaft in line with
the mark on the companion flange.
CAUTION:
Use paint to make the matching mark on the front drive
shaft. Do not damage the front drive shaft.
4. Remove the companion flange using suitable tool.
5. Remove the front oil seal from the front case using Tool.
CAUTION:
Do not damage front case.
INSTALLATION
LDIA0142E
SDIA2779E
WDIA0193E
Tool number
: ST33290001 (J-34286)
LDIA0144E
FRONT OIL SEAL
DLN-93
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
1. Install the new front oil seal until it is flush with the end face of
the front case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Align the matching mark of the front drive shaft with the match-
ing mark of the companion flange, then install the companion
flange.
3. Install the new self-lock nut and tighten to the specified torque
using suitable tool. Refer to
CAUTION:
Do not reuse self-lock nut.
4. Install the front propeller shaft. Refer to
.
5. Check for transfer fluid leaks. Check transfer fluid level and add
specified fluid as necessary. Refer to
.
Tool number
: KV38100500 ( — )
LDIA0145E
SDIA2214E
LDIA0147E
DLN-94
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
REAR OIL SEAL
REAR OIL SEAL
Removal and Installation
INFOID:0000000009886035
REMOVAL
1. Remove the rear propeller shaft. Refer to
DLN-139, "Removal and Installation"
2. Remove the dust cover from the rear case.
CAUTION:
Do not damage the rear case.
3. Remove oil cover from dust cover.
4. Remove the rear oil seal from the rear case using Tool.
CAUTION:
Do not damage the rear case.
INSTALLATION
1. Install the new rear oil seal until it is flush with the end face of the
rear case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Install the oil cover until it reaches the end face of the new dust cover.
3. Apply petroleum jelly to the circumference of the new dust cover
(1). Position the new dust cover as shown.
CAUTION:
• Do not reuse dust cover.
• Position the protrusions at the position shown.
• (2): Rear case assembly
• (A): Protrusions
WDIA0127E
Tool number
: ST33290001 (J-34286)
LDIA0139E
Tool number
: KV38100500 ( — )
LDIA0140E
AWDIA0550GB
REAR OIL SEAL
DLN-95
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4. Install the new dust cover to the rear case using Tool.
CAUTION:
• Do not reuse dust cover.
• Apply petroleum jelly to dust cover.
5. Install the rear propeller shaft. Refer to Refer to
(3S1410).
6. Check for transfer fluid leaks. Check transfer fluid level and add
specified fluid as necessary. Refer to
.
Tool number
: KV40105310 ( — )
PDIA0116E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст