Nissan Titan. Instruction — part 131
DLN-96
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
TRANSFER CONTROL DEVICE
TRANSFER CONTROL DEVICE
Removal and Installation
INFOID:0000000009886036
REMOVAL
1. Switch the 4WD shift switch to 2WD and set the transfer assembly to 2WD.
2. Disconnect the transfer control device harness connector.
3. Remove the breather hose from the transfer control device.
4. Remove the bolts (
) and detach the transfer control device.
INSTALLATION
1. Install the new O-ring to the transfer control device.
CAUTION:
• Do not reuse O-ring.
• Apply petroleum jelly to O-ring.
2. Install the transfer control device.
a. Turn the control shift rod fully counterclockwise using a flat-
bladed screwdriver, and then put a mark on the control shift rod.
b. Align the transfer control device shaft cutout with the mark on
the control shift rod, and install.
NOTE:
Turn the transfer control device when the transfer control device
connection does not match.
LDIA0136E
SDIA3378E
PDIA0119E
PDIA0120E
TRANSFER CONTROL DEVICE
DLN-97
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
c. Tighten the bolts (
) to the specified torque. Refer to
.
3. Install the breather hose to the transfer control device.
4. Connect the transfer control device harness connector.
5. After the installation, check the 4WD shift indicator pattern. If
NG, adjust the position between the transfer assembly and
transfer control unit. Refer to
DLN-82, "Precaution for Transfer
Assembly and Transfer Control Unit Replacement"
.
SDIA2212E
DLN-98
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
AIR BREATHER HOSE
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000009886037
COMPONENTS
REMOVAL
1. Disconnect air breather hose from transfer control device.
2. Disconnect air breather hose from breather tube (transfer).
3. Release air breather hose clamp and clips as necessary.
4. Disconnect air breather hoses from breather tube.
CAUTION:
Note paint marks for installation.
INSTALLATION
CAUTION:
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
1. Install each air breather hose into the breather tube (metal con-
nector) until the hose end reaches the end of the curved section.
Set each air breather hose with paint mark facing upward.
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Breather tube (transfer)
7.
Air breather hose clamp
8.
Transfer control device
SDIA3351E
SDIA3340E
AIR BREATHER HOSE
DLN-99
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
2. Install transfer control device air breather hose and transfer air
breather hose on clip A and clip B with the paint mark facing
upward.
3. Install clip C on transfer control device air breather hose and
transfer air breather hose with the paint mark matched.
4. Install transfer control device air breather hose and transfer air
breather hose on clip D with the paint mark facing upward.
5. Install transfer air breather hose (A) into the breather tube
(transfer, metal connector) until the hose end reaches the base
of the tube. Set transfer air breather hose with paint mark (B)
facing upward.
6. Install transfer control device air breather hose into transfer con-
trol device (case connector) until the hose end reaches the base
of the tube. Set transfer control device air breather hose with
paint mark facing forward.
SDIA3353E
SDIA3354E
SDIA3355E
AWDIA0784ZZ
SDIA3300E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст