Nissan Titan. Instruction — part 5
BR-10
< BASIC INSPECTION >
BRAKE MASTER CYLINDER
BRAKE MASTER CYLINDER
On Board Inspection
INFOID:0000000009883532
LEAK INSPECTION
Check for leaks at master cylinder to brake booster attachment point, reservoir tank, and brake tube connec-
tions.
BRAKE TUBE AND HOSE
BR-11
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE TUBE AND HOSE
Hydraulic Circuit
INFOID:0000000009883533
CAUTION:
• All hoses and piping (tubes) must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other parts when turning the steering wheel both clockwise
and counterclockwise.
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• Refill with new specified brake fluid. Refer to
MA-15, "FOR NORTH AMERICA : Fluids and Lubri-
MA-16, "FOR MEXICO : Fluids and Lubricants"
(Mexico).
• Do not reuse drained brake fluid.
FRONT BRAKE
FRONT BRAKE : Inspection
INFOID:0000000009883534
INSPECTION AFTER REMOVAL
CAUTION:
1.
Actuator
2.
Master cylinder
3.
Brake booster
4.
Connector
5.
Axle mounted connector
9.3 N·m (0.95 kg-m, 82 in-lb)
A.
Union bolt (front caliper)
18.2 N·m (1.9 kg-m, 13 ft-lb)
B.
Flare nut M12
18.2 N·m (1.9 kg-m, 13 ft-lb)
C.
Flare nut M10
16.2 N·m (1.7 kg-m, 12 ft-lb)
D.
Hose connection (rear caliper)
18.2 N·m (1.9 kg-m, 13 ft-lb)
E.
Flare nut to rear hose
16.2 N·m (1.7 kg-m, 12 ft-lb)
F.
Flare nut M10
13.0 N·m (1.3 kg-m, 10 ft-lb)
—
Brake line
=
Brake hose
AWFIA0960ZZ
BR-12
< BASIC INSPECTION >
BRAKE TUBE AND HOSE
Brake tubes and hoses are important safety parts. Always disassemble the parts and retighten their fit-
tings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part is
detected.
1. Check brake lines (tubes and hoses) and connections for fluid leaks, damage, twists, deformation, contact
with other parts, and loose connections. Replace any parts as necessary. Refer to
2. While depressing brake pedal under a force of 785 N (80 kg-f, 177 lb-f) with engine running for approxi-
mately 5 seconds, check each part for fluid leaks.
REAR BRAKE
REAR BRAKE : Inspection
INFOID:0000000009883535
INSPECTION AFTER REMOVAL
CAUTION:
Brake tubes and hoses are important safety parts. Always disassemble the parts and retighten their fit-
tings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part is
detected.
1. Check brake lines (tubes and hoses) and connections for fluid leaks, damage, twists, deformation, contact
with other parts, and loose connections. Replace any parts as necessary. Refer to
2. While depressing brake pedal under a force of 785 N (80 kg-f, 177 lb-f) with engine running for approxi-
mately 5 seconds, check each part for fluid leaks.
BRAKE PEDAL
BR-13
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
PERIODIC MAINTENANCE
BRAKE PEDAL
Inspection and Adjustment - Standard Pedal
INFOID:0000000009883536
INSPECTION
1. Inspect the brake pedal free height (H) from the floor using Tool
at a 90
° angle to the floor as shown.
2. Adjust the brake pedal height to specifications.
Unit: mm (in)
ADJUSTMENT
1. Loosen the stop lamp switch and ASCD cancel switch (if equipped) by turning 45
° counterclockwise.
Tool number :
—
(J-46532)
AWFIA0557ZZ
Brake Pedal Specifications
Pedal free height (H)
Pedal full stroke (S)
Clearance between brake pedal bracket (C
1
) and threaded end of stop lamp switch
and ASCD cancel switch [if equipped] (C
2
)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст