Nissan Titan. Instruction — part 282
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
EC-429
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
Description
INFOID:0000000009886871
NOTE:
If DTC P2101 is displayed with DTC P2100 or 2119, first perform the trouble diagnosis for DTC P2100
or P2119. Refer to
or
.
Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc.
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor and it provides feed-
back to the ECM to control the throttle control motor to make the throttle valve opening angle properly in
response to driving condition.
On Board Diagnosis Logic
INFOID:0000000009886872
This self-diagnosis has the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, ECM enters fail-safe mode and the MIL lights up.
DTC Confirmation Procedure
INFOID:0000000009886873
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next step.
1. Turn ignition swich OFF and wait at least 10 seconds.
2. Turn ignition swich ON.
3. Turn ignition swich OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11V when engine
is running.
1. Turn ignition switch ON and wait at least 2 seconds.
2. Start engine and let it idle for 5 seconds.
3. Check DTC.
4. If DTC is detected, go to
.
Diagnosis Procedure
INFOID:0000000009886874
1.
CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Loosen and retighten three ground screws on the body.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2101
2101
Electric throttle control
performance
Electric throttle control function does not oper-
ate properly.
• Harness or connectors
(Throttle control motor circuit is open or
shorted)
• Electric throttle control actuator
Engine operating condition in fail-safe mode
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return
spring.
EC-430
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
2.
CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-I
1. Check voltage between ECM terminal 3 and ground under the
following conditions with CONSULT or tester.
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 3.
3.
CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT-I
1. Turn ignition switch OFF.
2. Check voltage between ECM terminal 104 and ground with
CONSULT or tester.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 4.
4.
CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT-II
1. Disconnect ECM harness connector.
2. Disconnect IPDM E/R harness connector E122.
3. Check harness continuity between ECM terminal 104 and IPDM E/R terminal 47.
Refer to Wiring Diagram.
4. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK FUSE
1. Disconnect 20A fuse.
2. Check 20A fuse for blown.
OK or NG
BBIA0354E
Ignition switch
Voltage
OFF
Approximately 0V
ON
Battery voltage
(11 - 14V)
MBIB0028E
Voltage: Battery voltage
PBIB1171E
Continuity should exist.
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
EC-431
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
OK
>> GO TO 8.
NG
>> Replace 20A fuse.
6.
CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-II
1. Disconnect ECM harness connector.
2. Disconnect IPDM E/R harness connector E119.
3. Check harness continuity between ECM terminal 3 and IPDM E/R terminal 6.
Refer to Wiring Diagram.
4. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E2, F32
• Harness for open or short between ECM and IPDM E/R
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK INTERMITTENT INCIDENT
GI-39, "How to Check Terminal"
GI-42, "Intermittent Incident"
OK or NG
OK
>> Replace IPDM E/R. Refer to
PCS-28, "Removal and Installation of IPDM E/R"
.
NG
>> Repair or replace harness or connectors.
9.
CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN OR SHORT
1. Turn ignition switch OFF.
2. Disconnect electric throttle control actuator harness connector.
3. Disconnect ECM harness connector.
4. Check harness continuity between the following terminals.
Refer to Wiring Diagram.
5. Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 10.
NG
>> Repair or replace.
10.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1. Remove the intake air duct.
Continuity should exist.
Electric throttle control
actuator terminal
ECM terminal
Continuity
5
5
Should not exist
4
Should exist
6
5
Should exist
4
Should not exist
PBIB1480E
EC-432
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
P2101 ELECTRIC THROTTLE CONTROL FUNCTION
2. Check if foreign matter is caught between the throttle valve and
the housing.
OK or NG
OK
>> GO TO 11.
NG
>> Remove the foreign matter and clean the electric throttle
control actuator inside, and then perform throttle valve
closed position learning. Refer to
Valve Closed Position Learning"
11.
CHECK THROTTLE CONTROL MOTOR
EC-432, "Component Inspection"
OK or NG
OK
>> GO TO 12.
NG
>> GO TO 13.
12.
CHECK INTERMITTENT INCIDENT
GI-39, "How to Check Terminal"
and
GI-42, "Intermittent Incident"
OK or NG
OK
>> GO TO 13.
NG
>> Repair or replace harness or connectors.
13.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1. Replace the electric throttle control actuator.
2. Perform
EC-128, "Throttle Valve Closed Position Learning"
3. Perform
EC-129, "Idle Air Volume Learning"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009886875
THROTTLE CONTROL MOTOR
1. Disconnect electric throttle control actuator harness connector.
2. Check resistance between terminals 5 and 6.
3. If NG, replace electric throttle control actuator and go to next
step.
4. Perform
EC-128, "Throttle Valve Closed Position Learning"
5. Perform
EC-129, "Idle Air Volume Learning"
.
BBIA0364E
Resistance: Approximately 1 - 15
Ω [at 25 °C (77°F)]
PBIB2066E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст