Nissan Pathfinder (2009 year). Instruction — part 105
C1142 PRESS SENSOR
BRC-65
< COMPONENT DIAGNOSIS >
[TYPE 1]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
3.
REAR PRESSURE SENSOR INSPECTION
1.
Reconnect the rear pressure sensor and ABS actuator and electric unit (control unit) connectors.
2.
Perform the rear pressure sensor (PRESS SEN2) component inspection. Refer to
.
Is the inspection result normal?
YES
>> Perform self-diagnosis again. If the same results appear, replace the ABS actuator and electric
unit (control unit). Refer to
BRC-131, "Removal and Installation"
.
NO
>> Replace the rear pressure sensor.
Component Inspection
INFOID:0000000003937789
1.
CHECK DATA MONITOR
On “DATA MONITOR”, select “PRESS SENSOR” and “PRESS SEN2” and check the brake fluid pressure.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Replace the appropriate pressure sensor. Refer to
BR-47, "Disassembly and Assembly"
.
Special Repair Requirement
INFOID:0000000003937790
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-12, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
.
>> GO TO 2
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
Refer to
BRC-13, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
Condition
PRESS SENSOR
and PRESS SEN2
(DATA MONITOR)
With ignition switch turned ON and brake pedal released.
Approx. 0 bar
With ignition switch turned ON and brake pedal depressed.
Positive value
2009 Pathfinder
BRC-66
< COMPONENT DIAGNOSIS >
[TYPE 1]
C1143, C1144 STEERING ANGLE SENSOR
C1143, C1144 STEERING ANGLE SENSOR
Description
INFOID:0000000003937791
The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel,
and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication.
DTC Logic
INFOID:0000000003937792
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000003937793
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect ABS actuator and electric unit (control unit) connector.
3.
Disconnect steering angle sensor connector.
4.
Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminal.
5.
Reconnect connectors and then perform the self-diagnosis. Refer to
.
Is any item indicated on the self-diagnosis display?
YES
>> GO TO 2
NO
>> Poor connection of connector terminal. Repair or replace connector.
2.
CHECK STEERING ANGLE SENSOR HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect steering angle sensor connector.
DTC
Display item
Malfunction detected condition
Possible cause
C1143
ST ANG SEN CIRCUIT
Neutral position of steering angle sensor is dislocated, or
the steering angle sensor is malfunctioning.
• Harness or connector
• Steering angle sensor
• ABS actuator and electric unit
(control unit)
C1144
ST ANG SEN SIGNAL
Neutral position of steering angle sensor is not finished.
Self-diagnosis results
ST ANG SEN CIRCUIT
ST ANG SEN SIGNAL
2009 Pathfinder
C1143, C1144 STEERING ANGLE SENSOR
BRC-67
< COMPONENT DIAGNOSIS >
[TYPE 1]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
3.
Check continuity between steering angle sensor connector M47
terminal 2 and ground.
4.
Turn ignition switch ON.
5.
Check voltage between steering angle sensor connector M47
terminal 3 and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace malfunctioning components.
3.
CHECK DATA MONITOR
1.
Connect the steering angle sensor connector and ABS actuator and electric unit (control unit) connector.
2.
Perform the steering angle sensor component inspection. Refer to
BRC-67, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-131, "Removal and Installa-
.
NO
>> Replace steering angle sensor and adjust neutral position of steering angle sensor. Refer to
134, "Removal and Installation"
Component Inspection
INFOID:0000000003937794
1.
CHECK DATA MONITOR
Select “STR ANGLE SIG” in “DATA MONITOR” and check steering angle sensor signal.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Replace steering angle sensor and adjust neutral position of steering angle sensor. Refer to
134, "Removal and Installation"
Special Repair Requirement
INFOID:0000000003937795
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-12, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
.
>> GO TO 2
Steering angle sensor
—
Continuity
Connector
Terminal
M47
2
Ground
Yes
WFIA0399E
Steering angle sensor
—
Voltage
Connector
Terminal
M47
3
Ground
Battery voltage
AWFIA0023ZZ
Steering condition
STR ANGLE SIG (DATA MONITOR)
Driving straight
0
±
2.5
°
Turn 90
°
to left
Approx. +90
°
Turn 90
°
to right
Approx.
−
90
°
2009 Pathfinder
BRC-68
< COMPONENT DIAGNOSIS >
[TYPE 1]
C1143, C1144 STEERING ANGLE SENSOR
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
Refer to
BRC-13, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
2009 Pathfinder
C1155 BRAKE FLUID LEVEL SWITCH
BRC-69
< COMPONENT DIAGNOSIS >
[TYPE 1]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1155 BRAKE FLUID LEVEL SWITCH
Description
INFOID:0000000003937797
The brake fluid level switch converts the brake fluid level to an electric signal and transmits it to the ABS actu-
ator and electric unit (control unit).
DTC Logic
INFOID:0000000003937798
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
BRC-69, "Diagnosis Procedure (With VQ40DE)"
BRC-70, "Diagnosis Procedure (With VK56DE)"
.
NO
>> Inspection End
Diagnosis Procedure (With VQ40DE)
INFOID:0000000003937799
1.
CONNECTOR INSPECTION
1.
Disconnect ABS actuator and electric unit (control unit) connector and brake fluid level switch connector.
2.
Check the terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace as necessary.
2.
CHECK HARNESS BETWEEN BRAKE FLUID LEVEL SWITCH AND ABS ACTUATOR AND ELECTRIC
UNIT (CONTROL UNIT)
1.
Check continuity between ABS actuator and electric unit (control
unit) connector E125 (A) terminal 28 and brake fluid level switch
connector E21 (B) terminal 1.
2.
Check continuity between ABS actuator and electric unit (control
unit) connector E125 (A) terminal 28 and ground.
Is the inspection result normal?
YES
>> GO TO 3
DTC
Display item
Malfunction detected condition
Possible cause
C1155
BR FLUID LEVEL LOW
Brake fluid level is low or communication line between
the ABS actuator and electric unit (control unit) and brake
fluid level switch is open or shorted.
• Harness or connector
• Brake fluid level switch
• Brake fluid level
Self-diagnosis results
BR FLUID LEVEL LOW
ABS actuator and electric unit
(control unit)
Brake fluid level switch
Continuity
Connector
Terminal
Connector
Terminal
E125 (A)
28
E21 (B)
1
Yes
ABS actuator and electric unit (control unit)
—
Continuity
Connector
Terminal
E125 (A)
28
Ground
No
AWFIA0474ZZ
2009 Pathfinder
BRC-70
< COMPONENT DIAGNOSIS >
[TYPE 1]
C1155 BRAKE FLUID LEVEL SWITCH
NO
>> Repair or replace malfunctioning components.
3.
CHECK BRAKE FLUID LEVEL SWITCH GROUND
Check continuity between brake fluid level switch connector E21 ter-
minal 2 and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace malfunctioning components.
4.
CHECK BRAKE FLUID LEVEL SWITCH
Perform brake fluid level switch component inspection. Refer to
BRC-71, "Component Inspection"
.
Is the inspection result normal?
YES
>> Perform self-diagnosis again. If the same results appear, replace ABS actuator and electric unit
(control unit). Refer to
BRC-131, "Removal and Installation"
NO
>> Replace brake fluid level switch.
Diagnosis Procedure (With VK56DE)
INFOID:0000000004422011
INSPECTION PROCEDURE
1.
CONNECTOR INSPECTION
1.
Disconnect ABS actuator and electric unit (control unit) connector and brake fluid level switch connector.
2.
Check the terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace as necessary.
2.
CHECK HARNESS BETWEEN BRAKE FLUID LEVEL SWITCH AND ABS ACTUATOR AND ELECTRIC
UNIT (CONTROL UNIT)
1.
Check continuity between ABS actuator and electric unit (control
unit) connector E127 (A) terminal 8 and brake fluid level switch
connector E21 (B) terminal 1.
2.
Check continuity between ABS actuator and electric unit (control
unit) connector E127 (A) terminal 8 and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace malfunctioning components.
3.
CHECK BRAKE FLUID LEVEL SWITCH GROUND
Brake fluid level switch
—
Continuity
Connector
Terminal
E21
2
Ground
Yes
AWFIA0026ZZ
ABS actuator and electric unit
(control unit)
Brake fluid level switch
Continuity
Connector
Terminal
Connector
Terminal
E127 (A)
8
E21 (B)
1
Yes
ABS actuator and electric unit (control unit)
—
Continuity
Connector
Terminal
E127 (A)
8
Ground
No
AWFIA0025ZZ
2009 Pathfinder
C1155 BRAKE FLUID LEVEL SWITCH
BRC-71
< COMPONENT DIAGNOSIS >
[TYPE 1]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Check continuity between brake fluid level switch connector E21 ter-
minal 2 and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace malfunctioning components.
4.
CHECK BRAKE FLUID LEVEL SWITCH
Perform brake fluid level switch component inspection. Refer to
BRC-71, "Component Inspection"
.
Is the inspection result normal?
YES
>> Perform self-diagnosis again. If the same results appear, replace ABS actuator and electric unit
(control unit). Refer to
BRC-131, "Removal and Installation"
NO
>> Replace brake fluid level switch.
Component Inspection
INFOID:0000000003937800
1.
CHECK BRAKE FLUID LEVEL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect brake fluid level switch connector.
3.
Check continuity between brake fluid level switch terminals.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Replace brake fluid level switch.
Special Repair Requirement
INFOID:0000000003937801
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform neutral position adjustment for the steering angle sensor when replacing the ABS actuator
and electric unit (control unit). Refer to
BRC-12, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
.
>> GO TO 2
2.
CALIBRATION OF DECEL G SENSOR
Always perform calibration of decel G sensor when replacing the ABS actuator and electric unit (control unit).
Refer to
BRC-13, "CALIBRATION OF DECEL G SENSOR : Description"
.
>> END
Brake fluid level switch
—
Continuity
Connector
Terminal
E21
2
Ground
Yes
AWFIA0026ZZ
Brake fluid level switch
Condition
Continuity
Terminal
1
−
2
When brake fluid is full in the reser-
voir tank.
No
When brake fluid is empty in the
reservoir tank.
Yes
ALFIA0026ZZ
2009 Pathfinder
BRC-72
< COMPONENT DIAGNOSIS >
[TYPE 1]
C1156 ST ANG SEN COM CIR
C1156 ST ANG SEN COM CIR
Description
INFOID:0000000003937802
The steering angle sensor is connected to the ABS actuator and electric unit (control unit) in addition to CAN
lines. CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle
multiplex communication line with high data communication speed and excellent error detection ability. Many
electronic control units are equipped onto a vehicle, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC Logic
INFOID:0000000003937803
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000003937804
1.
CHECK CONNECTOR
1.
Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector, check
terminals for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminals.
2.
Reconnect connector and perform self-diagnosis. Refer to
BRC-26, "CONSULT-III Function (ABS)"
Is above displayed on the self-diagnosis display?
YES
>> Refer to
LAN-14, "Trouble Diagnosis Flow Chart"
NO
>> Inspection End
DTC
Display item
Malfunction detected condition
Possible cause
C1156
ST ANG SEN COM CIR
When steering angle sensor is not transmitting CAN
communication signal to the ABS actuator and electric
unit (control unit).
• Harness or connector
• CAN communication line
• Steering angle sensor
• ABS actuator and electric unit
(control unit)
Self-diagnosis results
ST ANG SEN COM CIR
Self-diagnosis results
CAN COMM CIRCUIT
ST ANG SEN COM CIR
2009 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст