Nissan Qashqai (2007-2010). Manual — part 1153
BACK DOOR
DLK-691
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR STAY : Exploded View
INFOID:0000000001098653
BACK DOOR STAY : Removal and Installation
INFOID:0000000001098656
REMOVAL
1.
Remove the stud ball (upper/lower), and then remove the back door stay.
2.
Remove the mounting bolts, and then remove the back door stay bracket (upper/lower).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check the back door open/close operation after installation.
BACK DOOR WEATHER-STRIP
BACK DOOR WEATHER-STRIP : Exploded View
INFOID:0000000001098657
REMOVAL
1.
Back door hinge
2.
Back door assembly
3.
Back door lock assembly
4.
Bumper rubber bracket
5.
Back door stay bracket (lower)
6.
Bumper rubber
7.
Back door stay
8.
Back door stay bracket (upper)
9.
Back door striker
Refer to
JMKIA0186ZZ
DLK-692
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY & SUPER LOCK]
BACK DOOR
BACK DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000001098659
REMOVAL
Pull up and remove engagement with body from the weatherstrip joint.
CAUTION:
After removal, do not pull strongly on the weather-strip.
INSTALLATION
1.
Working from the upper section, align the weatherstrip mark with vehicle center position mark and install
the weatherstrip onto the vehicle.
2.
For the lower section, align the weatherstrip seam with center of the back door striker.
3.
After installation, pull the weatherstrip gently to ensure that there is no loose section.
NOTE:
Make sure that the weatherstrip is fit tlightly at each corner and the luggage rear plate.
1.
Back door weatherstrip
A.
Mark (upper)
B.
Mark (lower)
JMKIA0184ZZ
FRONT DOOR LOCK
DLK-693
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000001098660
DOOR LOCK : Removal and Installation
INFOID:0000000001098661
REMOVAL
1.
Remove the front door finisher. Refer to
INT-10, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove the inside handle mounting bolt, and then disconnect the inside handle knob cable and the lock
knob cable.
3.
Remove the front door glass. Refer to
GW-19, "Removal and Installation"
.
4.
Remove the front door module assembly. Refer to
GW-22, "Removal and Installation"
.
5.
Disconnect the door antenna and the door request switch connector and remove the harness clamp
(models with Intelligent Key system).
1.
Outside handle assembly
2.
Door key cylinder
3.
Key cylinder lever
4.
Front gasket
5.
Rear gasket
6.
Outside handle bracket
7.
Inside handle
8.
Door lock assembly
9.
Key cylinder rod
10. Key rod protector
11.
Key rod protector assembly (RH
handle only)
12. Outside handle cover
13. Antenna
14. Outside handle base
A:
Intelligent Key only
Refer to
JMKIA0188GB
DLK-694
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY & SUPER LOCK]
FRONT DOOR LOCK
6.
Remove the door side grommet, and remove the door key cylin-
der assembly (driver side) and outside handle escutcheon (pas-
senger side) mounting bolts from grommet hole.
CAUTION:
Do not forcibly remove the bolts (TORX: T10).
7.
Reach in to separate the key cylinder rod connection (on the handle).
8.
Disconnect the door key cylinder switch harness connector.
9.
Remove the key cylinder lever from the door key cylinder.
10. While pulling the outside handle, remove door key cylinder
assembly.
11. Disconnect front door request switch harness connector (models with Intelligent Key system).
12. While pulling outside handle, slide toward rear of vehicle to
remove outside handle.
13. Remove the front gasket and the rear gasket.
JMKIA0020ZZ
PIIB5809E
PIIB5810E
PIIB5811E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст