Nissan Qashqai (2007-2010). Manual — part 1154
FRONT DOOR LOCK
DLK-695
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
14. Remove the door lock assembly mounting bolts (TORX: T30).
15. Disconnect the door lock actuator connector, and then remove
the door lock assembly.
16. While pulling the outside handle bracket, slide toward rear of
vehicle to remove the outside handle bracket.
17. Reach in to separate the outside handle cable connection.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• To install each rod, rotate the rod holder until a click is felt.
• Check the door lock/unlock operation after installation.
• Check the door open/close operation after installation.
INSIDE HANDLE
INSIDE HANDLE : Exploded View
INFOID:0000000001098666
MIIB0633E
PIIB5814E
PIIB5815E
DLK-696
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY & SUPER LOCK]
FRONT DOOR LOCK
INSIDE HANDLE : Removal and Installation
INFOID:0000000001098667
REMOVAL
1.
Remove the front door finisher. Refer to
INT-10, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove the inside handle mounting bolt.
3.
Disconnect the inside handle knob cable and the lock knob cable, and then remove the inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check the door lock/unlock operation after installation.
• Check the door open/close operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Exploded View
INFOID:0000000001098668
1.
Outside handle assembly
2.
Door key cylinder
3.
Key cylinder lever
4.
Front gasket
5.
Rear gasket
6.
Outside handle bracket
7.
Inside handle
8.
Door lock assembly
9.
Key cylinder rod
10. Key rod protector
11.
Key rod protector assembly (RH
handle only)
12. Outside handle cover
13. Antenna
14. Outside handle base
A:
Intelligent Key only
Refer to
for symbols in the figure.
JMKIA0188GB
FRONT DOOR LOCK
DLK-697
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000001098669
REMOVAL
1.
Remove the front door finisher. Refer to
INT-10, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove the inside handle mounting bolt, and disconnect the inside handle knob cable and the lock knob
cable.
3.
Remove the front door glass. Refer to
GW-19, "Removal and Installation"
.
4.
Remove the front door module assembly. Refer to
GW-22, "Removal and Installation"
.
5.
Disconnect the door antenna and the door request switch connector and remove the harness clamp
(models with Intelligent Key system).
6.
Remove the door side grommet, and remove the door key cylin-
der assembly (driver side) and the outside handle escutcheon
(passenger side) mounting bolts from the grommet hole.
CAUTION:
Do not forcibly remove the bolts (TORX: T10).
1.
Outside handle assembly
2.
Door key cylinder
3.
Key cylinder lever
4.
Front gasket
5.
Rear gasket
6.
Outside handle bracket
7.
Inside handle
8.
Door lock assembly
9.
Key cylinder rod
10. Key rod protector
11.
Key rod protector assembly (RH
handle only)
12. Outside handle cover
13. Antenna
14. Outside handle base
A:
Intelligent Key only
Refer to
JMKIA0188GB
JMKIA0020ZZ
DLK-698
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY & SUPER LOCK]
FRONT DOOR LOCK
7.
Reach in to separate the key cylinder rod connection (on the handle).
8.
Disconnect the door key cylinder switch harness connector.
9.
Remove the key cylinder lever from the door key cylinder.
10. While pulling the outside handle, remove the door key cylinder
assembly.
11. Disconnect the front door request switch harness connector (models with Intelligent Key system).
12. While pulling the outside handle, slide toward rear of vehicle to
remove the outside handle.
13. Remove the front gasket and rear gasket.
14. While pulling the outside handle bracket, slide toward rear of
vehicle to remove the outside handle bracket.
PIIB5809E
PIIB5810E
PIIB5811E
PIIB5814E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст