Nissan Qashqai (2007-2010). Manual — part 1436
REAR WIPER MOTOR CIRCUIT
WW-35
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Does continuity exist?
YES
>> GO TO 4.
NO
>> Repair the harnesses or connectors.
4.
CHECK REAR WIPER MOTOR SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Repair the harnesses or connectors.
NO
>> Replace BCM. Rrefer to
BCM
Rear wiper motor
Continuity
Connector
Terminal
Connector
Terminal
M66
43
D156
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M66
43
Not existed
WW-36
< COMPONENT DIAGNOSIS >
REAR WIPER AUTO STOP SIGNAL CIRCUIT
REAR WIPER AUTO STOP SIGNAL CIRCUIT
Component Function Check
INFOID:0000000000903201
1.
CHECK REAR WIPER (AUTO STOP) OPERATION
CONSULT-III DATA MONITOR
1.
Select "WIPER" of BCM data monitor item.
2.
Operate the rear wiper.
3.
Check that "RR WIPER STOP" changes to "ON" and "OFF" linked with the wiper operation.
Is the status of item normal?
YES
>> Rear wiper auto stop signal circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000000903200
1.
CHECK REAR WIPER MOTOR (AUTO STOP) OUTPUT VOLTAGE
1.
Turn the ignition switch OFF.
2.
Disconnect rear wiper motor connector.
3.
Turn the ignition switch ON.
4.
Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REAR WIPER MOTOR (AUTO STOP) SHORT CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Repair the harnesses or connectors.
NO
>> Replace BCM. Refer to
3.
CHECK REAR WIPER MOTOR (AUTO STOP) CIRCUIT CONTINUITY
1.
Check continuity between BCM harness connector and rear wiper motor harness connector.
Monitor item
Condition
Monitor
status
RR WIPER STOP
Rear wiper motor
Stop position
ON
Except stop posi-
tion
OFF
Terminals
Voltage
(Approx.)
(+)
(
−
)
BCM
Ground
Connector
Terminal
M66
44
Battery voltage
BCM
Ground
Continuity
Connector
Terminal
M66
44
Not existed
REAR WIPER AUTO STOP SIGNAL CIRCUIT
WW-37
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Does continuity exist?
YES
>> Replace rear wiper motor.
NO
>> Repair the harnesses or connectors.
BCM Rear
wiper
motor
Continuity
Connector
Terminal
Connector
Terminal
M66
44
D156
2
Existed
WW-38
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER RELAY
HEADLAMP WASHER RELAY
Component Inspection
INFOID:0000000000903229
1.
CHECK HEADLAMP WASHER RELAY
1.
Turn the ignition switch OFF.
2.
Disconnect headlamp washer relay.
3.
Apply battery voltage to headlamp washer relay between terminals 3 and 4.
4.
Check continuity of headlamp washer relay.
Does continuity exist?
YES
>> Headlamp washer relay is normal.
NO
>> Replace headlamp washer relay.
Headlamp washer relay
Condition
Continuity
Terminal
Voltage
1
2
Apply
Existed
Not Apply
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст