Nissan Qashqai (2007-2010). Manual — part 1435
FRONT WIPER MOTOR GROUND CIRCUIT
WW-31
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER MOTOR GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000000924453
1.
CHECK FRONT WIPER MOTOR (GROUND) OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect front wiper motor connector.
3.
Check continuity between front wiper motor harness connector and ground.
Does continuity exist?
YES
>> Front wiper motor ground circuit is normal.
NO
>> Repair the harnesses or connectors.
Front wiper motor
Ground
Continuity
Connector
Terminal
E20
5
Existed
WW-32
< COMPONENT DIAGNOSIS >
WASHER SWITCH
WASHER SWITCH
Description
INFOID:0000000000896851
• Washer switch is integrated with combination switch.
• Combination switch switches polarity between front washer operating and rear washer operating to supply
power to the washer pump on ground.
Component Inspection
INFOID:0000000000896852
1.
CHECK WIPER SWITCH
1.
Turn the ignition switch OFF.
2.
Disconnect combination switch connector.
3.
Check continuity between the combination switch terminals.
Does continuity exist?
YES
>> Wiper and washer switch is normal.
NO
>> Replace wiper and washer switch.
JPLIA0163GB
A
: Terminal 14
B
: Terminal 12
C
: Terminal 13
D
: Terminal 11
JPLIA0164GB
Combination switch
Condition
Continuity
Terminal
11
12
Front washer switch ON
Existed
13
14
11
14
Rear washer switch ON
12
13
RAIN SENSOR
WW-33
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
RAIN SENSOR
Description
INFOID:0000000000984465
Detects water droplets on the windshield with infrared rays, and transmits the rain sensor signal to BCM
through the light and rain sensor serial link.
Diagnosis Procedure
INFOID:0000000000907640
EXL-69, "Component Function Check"
.
WW-34
< COMPONENT DIAGNOSIS >
REAR WIPER MOTOR CIRCUIT
REAR WIPER MOTOR CIRCUIT
Component Function Check
INFOID:0000000000903198
1.
CHECK REAR WIPER ON OPERATION
CONSULT-III ACTIVE TEST
1.
Select "RR WIPER" of BCM active test item.
2.
With operating the test item, check rear wiper operation.
Is rear wiper operation normally?
YES
>> Rear wiper motor circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000000903199
1.
CHECK REAR WIPER MOTOR OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Turn the ignition switch OFF.
2.
Disconnect rear wiper motor connector.
3.
Turn the ignition switch ON.
4.
Select "RR WIPER" of BCM active test item.
5.
With operating the test item, check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK REAR WIPER MOTOR GROUND OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Check continuity between rear wiper motor harness connector and ground.
Does continuity exist?
YES
>> Replace rear wiper motor.
NO
>> Repair the harnesses or connectors.
3.
CHECK REAR WIPER MOTOR OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and rear wiper motor harness connector.
ON
: Rear wiper ON operation
OFF
: Stop the rear wiper.
Terminals
Test item
Voltage
(Approx.)
(+)
(
−
)
BCM
Ground
REAR WIPER
Connector
Terminal
M66
43
ON
Battery
voltage
OFF
0 V
Rear wiper motor
Ground
Continuity
Connector
Terminal
D156
1
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст