Nissan Qashqai (2007-2010). Manual — part 1342

HAZARD SWITCH

EXL-73

< COMPONENT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Does continuity exist?

YES

>> Repair the harnesses or connectors.

NO

>> GO TO 4.

4.

CHECK HAZARD SWITCH GROUND OPEN CIRCUIT

Check continuity between the hazard switch harness connector and the ground.

Does continuity exist?

YES

>> Replace the hazard switch.

NO

>> Repair the harnesses or connectors.

Hazard switch

Ground

Continuity

Connector

Terminal

M45

3

Not existed

Hazard switch

Ground

Continuity

Connector

Terminal

M45

2

Existed

EXL-74

< COMPONENT DIAGNOSIS >

[XENON TYPE]

TAIL LAMP CIRCUIT

TAIL LAMP CIRCUIT

Component Function Check

INFOID:0000000000955463

1.

CHECK TAIL LAMP OPERATION

IPDM E/R AUTO ACTIVE TEST

1.

Activate IPDM E/R auto active test. Refer to

PCS-9, "Diagnosis Description"

.

2.

Check that the tail lamp is turned ON.

CONSULT-III ACTIVE TEST

1.

Select "EXTERNAL LAMP" of IPDM E/R active test item.

2.

With operating the test items, check that the tail lamp is turned ON.

Is the tail lamp turned ON?

YES

>> Tail lamp circuit is normal.

NO

>> Refer to

EXL-74, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000000955464

1.

CHECK TAIL LAMP FUSE

1.

Turn the ignition switch OFF.

2.

Check that the following fuses are not fusing.

Is the fuse fusing?

YES

>> Repair the malfunctioning part before replacing the fuse.

NO

>> GO TO 2.

2.

CHECK TAIL LAMP OUTPUT VOLTAGE

CONSULT-III ACTIVE TEST

1.

Disconnect the rear combination lamp connector.

2.

Turn the ignition switch ON.

3.

Select "EXTERNAL LAMP" of IPDM E/R active test item.

4.

With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Replace IPDM E/R.

3.

CHECK TAIL LAMP OPEN CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R connector.

TAIL

: Tail lamp ON

OFF

: Tail lamp OFF

Unit

Location

Fuse No.

Capacity

• Tail lamp
• License plate lamp

IPDM E/R

#49

10 A

Terminals

Test item

Voltage

(Approx.)

(+)

(

−

)

IPDM E/R

Ground

EXTERNAL

LAMP

Connector

Terminal

E13

38

TAIL

Battery volt-

age

OFF

0 V

TAIL LAMP CIRCUIT

EXL-75

< COMPONENT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

3.

Check continuity between the IPDM E/R harness connector and the rear combination lamp harness con-
nector.

Does continuity exist?

YES

>> GO TO 4.

NO

>> Repair the harnesses or connectors.

4.

CHECK TAIL LAMP GROUND OPEN CIRCUIT

Check continuity between the rear combination lamp harness connector and the ground.

Does continuity exist?

YES

>> Replace the rear combination lamp.

NO

>> Repair the harnesses or connectors.

IPDM E/R

Rear combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E13

38

B59

2

Existed

LH

B80

2

Rear combination lamp

Ground

Continuity

Connector

Terminal

RH

B59

4

Existed

LH

B80

4

EXL-76

< COMPONENT DIAGNOSIS >

[XENON TYPE]

LICENSE PLATE LAMP CIRCUIT

LICENSE PLATE LAMP CIRCUIT

Component Function Check

INFOID:0000000000955465

NOTE:
Check the tail lamp circuit if the tail lamp and the license plate lamp are not turned ON.

1.

CHECK LICENSE PLATE LAMP OPERATION

IPDM E/R AUTO ACTIVE TEST

1.

Activate IPDM E/R auto active test. Refer to

PCS-9, "Diagnosis Description"

.

2.

Check that the license plate lamp is turned ON.

CONSULT-III ACTIVE TEST

1.

Select "EXTERNAL LAMP" of IPDM E/R active test item.

2.

With operating the lighting switch, check that the license plate lamp is turned ON.

Is the license plate lamp turned ON?

YES

>> License plate lamp circuit is normal.

NO

>> Refer to

EXL-76, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000000955466

1.

CHECK LICENSE PLATE LAMP BULB

Check the applicable lamp bulb.

Is the bulb normal?

YES

>> GO TO 2.

NO

>> Replace the bulb.

2.

CHECK LICENSE PLATE LAMP OPEN CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R connector and the license plate lamp connector.

3.

Check continuity between the IPDM E/R harness connector and the license plate lamp harness connec-
tor.

Does continuity exist?

YES

>> GO TO 3.

NO

>> Repair the harnesses or connectors.

3.

CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT

Check continuity between the license plate lamp harness connector and the ground.

Does continuity exist?

YES

>> Replace the license plate lamp.

NO

>> Repair the harnesses or connectors.

TAIL

: License plate lamp ON

OFF

: License plate lamp OFF

IPDM E/R

License plate lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E13

38

D185

1

Existed

LH

D184

1

License plate lamp

Ground

Continuity

Connector

Terminal

RH

D185

2

Existed

LH

D184

2