Nissan Qashqai (2007-2010). Manual — part 1194
BACK DOOR
DLK-855
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After installation, perform fitting adjustment. Refer to
DLK-855, "BACK DOOR ASSEMBLY : Adjust-
• Check the back door open/close operation after installation.
• Check the back door lock/unlock operation after installation.
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000001098769
FITTING ADJUSTMENT
1.
Check the clearance and the evenness between the back door and each part visually and by touching.
(Fitting standard dimension in the table below shall be satisfied.)
2.
In case any parts are out of specification, adjust them according to the procedures shown below.
3.
Loosen the bumper rubber.
4.
Loosen the back door striker mounting bolts.
5.
Lift up the back door approximately 100 – 150 mm (3.937 – 5.906 in) height then close it lightly and check
that it is engaged firmly with the back door closed.
6.
Check the clearance and evenness.
7.
Finally tighten the back door striker.
BACK DOOR STRIKER
BACK DOOR STRIKER : Exploded View
INFOID:0000000001098771
Portion
Standard
Difference(RH/LH)
Back door panel –
Roof panel
A – A
F
Clearance
5.0 – 7.0 mm
(0.197 – 0.276 in)
—
G
Surface height
0.0 – 2.0 mm
(0.000 – 0.079 in)
—
Back door glass –
Body side outer
B – B
H
Clearance
3.9 – 8.1 mm
(0.154 – 0.319 in)
2.1 mm (0.083 in)
I
Surface height
- 1.0 – 3.1 mm
(- 0.039 – 0.122 in)
2.0 mm (0.079 in)
Back door panel –
Body side outer
C – C
J
Clearance
3.5 – 6.5 mm
(0.138 – 0.256 in)
2.0 mm (0.079 in)
K
Surface height
- 1.0 – 1.0 mm
(- 0.039 – 0.039 in)
—
Back door panel –
Rear bumper fascia
D – D
L
Clearance
4.0 – 8.0 mm
(0.157 – 0.315 in)
2.0 mm (0.079 in)
M
Surface height
0.1 – 4.1 mm
(0.004 – 0.161 in)
2.1 mm (0.083 in)
Back door panel –
Rear bumper fascia
E – E
N
Clearance
5.8 – 10.2 mm
(0.228 – 0.402 in)
—
DLK-856
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY, WITH SUPER LOCK]
BACK DOOR
BACK DOOR STRIKER : Removal and Installation
INFOID:0000000001098773
REMOVAL
1.
Remove the luggage rear plate cap. Refer to
INT-24, "Removal and Installation"
2.
Remove the mounting bolts, and then remove the back door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• When removing and installing the back door striker, be sure to perform the fitting adjustment. Refer
DLK-855, "BACK DOOR ASSEMBLY : Adjustment"
• Check the back door open/close operation after installation.
BACK DOOR HINGE
BACK DOOR HINGE : Exploded View
INFOID:0000000001102427
1.
Back door hinge
2.
Back door assembly
3.
Back door lock assembly
4.
Bumper rubber bracket
5.
Back door stay bracket (lower)
6.
Bumper rubber
7.
Back door stay
8.
Back door stay bracket (upper)
9.
Back door striker
Refer to
for symbols in the figure.
JMKIA0186ZZ
BACK DOOR
DLK-857
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY, WITH SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR HINGE : Removal and Installation
INFOID:0000000001102428
REMOVAL
1.
Remove the back door assembly. Refer to
DLK-248, "BACK DOOR ASSEMBLY : Removal and Installa-
2.
Remove upper side of the back door weatherstrip. Refer to
DLK-254, "BACK DOOR WEATHER-STRIP :
.
3.
Remove rear seat belt cover. Refer to
INT-21, "Removal and Installation"
4.
Using remover tool, remove the headlining clip at the rear side of the headlining.
Refer to
.
5.
Remove the rear side of the headlining.
6.
Remove the back door hinge mounting nuts (body side), and then remove the back door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• When removing and installing the back door assembly, perform the fitting adjustment. Refer to
250, "BACK DOOR ASSEMBLY : Adjustment"
.
• After installation, apply touch-up paint (the body color) onto the head of the hinge mounting nuts.
• Check the hinge rotating part for poor lubrication. If necessary, apply body grease.
• Check the back door open/close operation after installation.
BACK DOOR STAY
1.
Back door hinge
2.
Back door assembly
3.
Back door lock assembly
4.
Bumper rubber bracket
5.
Back door stay bracket (lower)
6.
Bumper rubber
7.
Back door stay
8.
Back door stay bracket (upper)
9.
Back door striker
Refer to
JMKIA0186ZZ
DLK-858
< ON-VEHICLE REPAIR >
[WITHOUT I-KEY, WITH SUPER LOCK]
BACK DOOR
BACK DOOR STAY : Exploded View
INFOID:0000000001098774
BACK DOOR STAY : Removal and Installation
INFOID:0000000001098777
REMOVAL
1.
Remove the stud ball (upper/lower), and then remove the back door stay.
2.
Remove the mounting bolts, and then remove the back door stay bracket (upper/lower).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check the back door open/close operation after installation.
BACK DOOR WEATHER-STRIP
BACK DOOR WEATHER-STRIP : Exploded View
INFOID:0000000001098778
REMOVAL
1.
Back door hinge
2.
Back door assembly
3.
Back door lock assembly
4.
Bumper rubber bracket
5.
Back door stay bracket (lower)
6.
Bumper rubber
7.
Back door stay
8.
Back door stay bracket (upper)
9.
Back door striker
Refer to
for symbols in the figure.
JMKIA0186ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст