Nissan Qashqai (2007-2010). Manual — part 599
CONTROL CABLE
TM-331
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
9.
Remove control cable (1) from bracket (2).
10. Remove the control cable from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing the control cable (1) to the control device assembly
(2), make sure that the control cable is fully pressed in with the
ribbed (A) surface facing upward.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing the control device. Refer to
TM-324, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLATION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-324, "Inspection and Adjustment"
: Vehicle front
JPDIA0107ZZ
JPDIA0078ZZ
TM-332
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
KEY INTERLOCK CABLE
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000000941127
Removal and Installation
INFOID:0000000000941125
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal/installation.
1.
Move selector lever to “P” position.
2.
Removal selector lever knob. Refer to
3.
Removal center console. Refer to
.
4.
Slide slider (A) toward casing cap (B) while pressing tabs (C) on
slider to separate slider from adjust holder (D).
5.
Remove steering column lower cover and lower instrument
panel, driver side. Refer to
.
1.
Key cylinder
2.
Control device assembly
3.
Key interlock cable
A.
Clip
JPDIA0098ZZ
E
: Key interlock rod
SCIA6975E
KEY INTERLOCK CABLE
TM-333
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6.
Remove clip (A) from holder (B) and remove key inter lock cable
(1) from key cylinder (2).
7.
Remove clip (
) and remove key inter lock cable (1).
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Install key interlock cable in such a way that it will not be damaged by sharp bends, twists or interfer-
ence with adjacent parts.
• After installing key interlock cable to control device assembly, make sure that casing cap and
bracket are firmly secured in their positions.
• Temporarily install adjust holder (A) to key interlock rod (B). Install
casing cap (C) to cable bracket (D) on control device assembly.
CAUTION:
• Never bend or twist key interlock cable excessively when
installing.
• After installing key interlock cable to cable bracket on con-
trol device assembly, make sure casing caps is firmly
secured in cable bracket on control device assembly.
• If casing cap is loose [less than 39.2 N (4.0 kg, 8.8 lb) remov-
ing force], replace key interlock cable.
JPDIA0099ZZ
JPDIA0100ZZ
JPDIA0097ZZ
TM-334
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
KEY INTERLOCK CABLE
• With the detent rod (A) pressed fully to the end, slider the key inter-
lock cable slider (B) to the key interlock rod side (C), and install
adjust holder (D) and key interlock rod.
CAUTION:
• Never press tabs when holding slider.
• Never apply any force at the right angle to key interlock rod
when slider.
JPDIA0315ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст