Nissan Qashqai (2007-2010). Manual — part 101
OIL FILTER
LU-17
< ON-VEHICLE MAINTENANCE >
[MR20DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL FILTER
Removal and Installation
INFOID:0000000000902591
REMOVAL
• Using oil filter wrench [SST: KV10115801] (A), remove oil filter.
CAUTION:
• Oil filter is provided with relief valve. Use Genuine NISSAN
Oil Filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any engine
oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine and vehicle.
INSTALLATION
1.
Remove foreign materials adhering to the oil filter installation surface.
2.
Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3.
Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.
Inspection
INFOID:0000000000902593
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
2.
Start the engine, and check there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
1
: Oil pan (lower)
: Vehicle front
PBIC3916E
SMA010
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
SMA229B
LU-18
< ON-VEHICLE REPAIR >
[MR20DE]
OIL COOLER
ON-VEHICLE REPAIR
OIL COOLER
Exploded View
INFOID:0000000000902598
Removal and Installation
INFOID:0000000000902599
REMOVAL
WARNING:
Be careful not to get burn yourself, as engine oil and engine coolant may be hot.
1.
Drain engine coolant from radiator and cylinder block. Refer to
.
2.
Using oil filter wrench [SST: KV10115801], remove oil filter. Refer to
LU-17, "Removal and Installation"
.
3.
Disconnect water hoses from oil cooler.
• When removing oil cooler only, pinching water hoses near oil cooler to prevent engine coolant from spill-
ing out.
• Remaining engine coolant in piping will come out. Use a tray to collect it.
CAUTION:
Perform this step when the engine is cold.
4.
Remove connector bolt, and remove oil cooler.
NOTE:
For reference when installing, put a matching mark on oil cooler and oil pan (upper).
INSTALLATION
1.
Water hose
2.
Water hose
3.
O-ring
4.
Oil cooler
5.
Connector bolt
6.
Oil filter
7.
Bracket
A.
for symbol marks in the figure.
PBIC3917E
OIL COOLER
LU-19
< ON-VEHICLE REPAIR >
[MR20DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
Installation in the reverse order of removal.
• Tighten the connecting bolt (2) after aligning the stopper (A) on the
oil pan (upper) side with protrusion of oil cooler (1).
Inspection
INFOID:0000000000902600
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to
2.
Start the engine, and check there is no leaks of engine oil or engine coolant.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level and the engine coolant level again. Refer to
: Engine front
PBIC3918E
LU-20
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR20DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000000902604
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(lmp qt)
Engine Oil Pressure
INFOID:0000000000902605
*: Engine oil temperature at 80
°
C (176
°
F)
Drain and refill
With oil filter change
4.4 (3-7/8)
Without oil filter change
4.2 (3-3/4)
Dry engine (Overhaul)
5.2 (4-5/8)
Engine speed (rpm)
Approximate discharge pressure* [kPa (bar, kg/cm
2
, psi)]
Idle speed
More than 80 (0.80, 0.8, 12)
2,000
More than 450 (4.50, 4.6, 65)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст