Nissan Qashqai (2007-2010). Manual — part 102
PRECAUTIONS
LU-21
< PRECAUTION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Liquid Gasket
INFOID:0000000001062305
REMOVAL OF LIQUID GASKET
• After removing the mounting bolts and nuts, separate the mating
surface using a seal cutter and remove the liquid gasket.
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to
lightly tap the gasket applied area.
CAUTION:
If for some unavoidable reason a tool such as a flat-bladed
screwdriver is used, be careful not to damage the mating sur-
faces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old liquid gasket adhering to the
gasket application surface and the mating surface.
• Remove the liquid gasket completely from the groove of the
gasket application surface, mounting bolts and bolt holes.
2.
Wipe the gasket application surface and the mating surface with
white gasoline (lighting and heating use) to remove adhering
moisture, grease and foreign materials.
3.
Attach the liquid gasket to the tube presser.
Use Genuine Liquid Gasket or equivalent.
4.
Apply the gasket without breaks to the specified location with the
specified dimensions.
• If there is a groove for the liquid gasket application, apply the
gasket to the groove.
• As for the bolt holes, normally apply the gasket inside the
holes. If specified, it should be applied outside the holes. Make
sure to read the manual in this instruction.
• Within five minutes of gasket application, install the mating
component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten after the installation.
• After 30 minutes or more have passed from the installation, fill
the engine oil and coolant.
CAUTION:
If there are manuals in this instruction, observe them.
PBIC0275E
PBIC0003E
EMA0622D
SEM159F
LU-22
< PREPARATION >
[K9K]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000001062306
Commercial Service Tools
INFOID:0000000001115769
NISSAN tool number
(RENAULT tool number)
Tool name
Description
KV113C0010
(Mot.1329)
Oil filter wrench
Removing and installing oil filter
KV113E0020
(Mot.836-05)
Oil pressure gauge set
Measuring oil pressure
Use C, E, F.
MBIB0369E
MBIB0663E
NISSAN tool number
Tool name
Description
WS39930000
Tube presser
Pressing the tube of liquid gasket
S-NT052
ENGINE OIL
LU-23
< ON-VEHICLE MAINTENANCE >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
ON-VEHICLE MAINTENANCE
ENGINE OIL
Inspection
INFOID:0000000001062307
OIL LEVEL AND MUDDINESS
• Before starting the engine, check the oil level placing vehicle hori-
zontally. If the engine is already started, stop it and allow 10 min-
utes before checking.
• Make sure the oil level is within the range shown in the figure.
• If it is out of range, adjust it.
• Check the oil for white turbidity or remarkable contamination.
• If the oil becomes turbid and white, it is highly probable that it is
contaminated with coolant. Find the cause and repair.
OIL LEAKAGE
Check for oil leakage around the following area.
• Oil pan
• Oil pan drain plug
• Oil pressure switch
• Oil filter bracket
• Vacuum pump
• Oil pump housing
• Mating surface between cylinder block and cylinder head
• Mating surface between cylinder head and rocker cover
• Oil cooler
• Crankshaft oil seals
OIL PRESSURE CHECK
WARNING:
• Be careful not to burn yourself, as the engine oil is hot.
• Oil pressure check should be done in Neutral “N” position.
1.
Check the oil level.
2.
Remove engine undercover.
3.
Remove the oil pressure switch to connect the oil pressure
gauge [SST: KV113E0020 (Mot. 836-05)].
4.
After warming up the engine, make sure oil pressure corre-
sponding to the engine speed is produced.
5.
After checking, install the oil pressure switch as follows.
a.
Remove old sealant adhering to the switch and engine.
b.
Apply thread sealant.
Use Genuine Liquid Gasket or equivalent.
6.
Start engine and check for oil leakage.
Draining
INFOID:0000000001062308
MBIB0548E
Idle speed
: Refer to
3000 rpm
: Refer to
Oil pressure switch:
: 25 N·m (2.55 kg-m, 18.4 ft-lb)
MBIB0549E
LU-24
< ON-VEHICLE MAINTENANCE >
[K9K]
ENGINE OIL
WARNING:
• Be careful not to burn yourself, as the engine oil is hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer: try to avoid direct skin
contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as
possible.
1.
Put vehicle horizontally.
2.
Warm up engine, and check for oil leakage from engine components.
3.
Stop engine and wait for 10 minutes.
4.
Loosen oil filler cap.
5.
Remove drain plug and then drain engine oil.
Refilling
INFOID:0000000001062309
1.
Refill with new engine oil.
• Refer to
MA-21, "Fluids and Lubricants"
.
• The refill capacity depends on the oil temperature and drain time.
Use these specifications for reference only.
Always use the dipstick to the determine when the proper amount
of oil is in the engine.
CAUTION:
• Be sure to clean drain plug and install with new washer.
• The refill capacity depends on the oil temperature and drain time. Use these specifications for ref-
erence only.
Always use the dipstick to the determine when the proper amount of oil is in the engine.
2.
Warm up engine and check area around drain plug and oil filter for oil leakage.
3.
Stop engine and wait for 10 minutes.
4.
Check oil level.
Oil capacity (Approximate)
: Refer to
"Periodical Maintenance Specification"
.
MBIB0548E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст