Nissan Qashqai (2007-2010). Manual — part 1107
FRONT DOOR
DLK-507
< ON-VEHICLE REPAIR >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Disconnect the front door harness connector.
4.
Remove the door hinge mounting nuts (door side), and then remove the door assembly.
CAUTION:
• When removing and installing the front door assembly, support the door with a jack and cloth to
protect the door and body.
• Perform work with 2 workers, because of its heavy weight.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• When removing and installing the front door assembly, perform the fitting adjustment. Refer to
842, "DOOR ASSEMBLY : Adjustment"
.
• After installation, apply touch-up paint (the body color) onto the head of the door hinge mounting
nuts.
• Check the door hinge rotating part for poor lubrication. If necessary, apply body grease.
• Check the front door open/close operation after installation.
DOOR ASSEMBLY : Adjustment
INFOID:0000000001098481
CLEARANCE, SURFACE HEIGHT AND SURFACE MISMATCH ADJUSTMENT
1.
Check the clearance and surface height and surface mismatch between the front door and each part
visually and by touching. (Fitting standard dimension in the table below shall be satisfied.)
2.
In case any parts are out of specification, adjust them according to the procedures shown below.
3.
Remove the front fender. Refer to refer to
DLK-838, "Removal and Installation"
4.
Loosen the door hinge mounting nuts on door side.
5.
Adjust the surface height and surface mismatch of the front door according to the fitting standard dimen-
sion.
6.
Temporarily tighten the hinge mounting nuts on door side.
7.
Loosen the door hinge mounting bolts on body side.
8.
Raise the front door at rear end to adjust clearance of the front door according to the fitting standard
dimension.
9.
After adjustment tighten bolts and nuts to the specified torque.
10. Install the front fender. Refer to refer to
DLK-838, "Removal and Installation"
.
CAUTION:
After installation, check the front fender adjustment. Refer to
DOOR STRIKER ADJUSTMENT
Adjust the door striker so that it becomes parallel with the lock inser-
tion direction.
Portion
Clearance
Surface height
Front fender – Front door
A – A
3.5 – 5.0 mm
(0.138 – 0.197 in)
- 1.5 – 0.5 mm
(- 0.059 – 0.020 in)
Front door – Rear door
B – B
3.5 – 5.0 mm
(0.138 – 0.197 in)
- 1.5 – 0.5 mm
(- 0.059 – 0.020 in)
PIIB2804J
DLK-508
< ON-VEHICLE REPAIR >
[WITH I-KEY & SUPER LOCK]
FRONT DOOR
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000001098484
DOOR STRIKER : Removal and Installation
INFOID:0000000001098485
REMOVAL
Remove the mounting bolts (A), and then remove the door striker
(1).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check the front door open/close operation after installation.
• When removing and installing the door striker, be sure to perform the fitting adjustment. Refer to
DLK-842, "DOOR ASSEMBLY : Adjustment"
DOOR HINGE
1.
Door check link
2.
Door hinge (upper)
3.
Door check link cover
4.
Door hinge (lower)
5.
Bracket
6.
Bumper rubber
7.
Front door panel
8.
Door striker
Refer to
for symbols in the figure.
JMKIA0179ZZ
JMKIA0439ZZ
FRONT DOOR
DLK-509
< ON-VEHICLE REPAIR >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR HINGE : Exploded View
INFOID:0000000001098488
DOOR HINGE : Removal and Installation
INFOID:0000000001098490
REMOVAL
1.
Remove the front door assembly. Refer to
DLK-841, "DOOR ASSEMBLY : Removal and Installation"
.
2.
Remove the door hinge mounting bolts, and then remove the front door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• When removing and installing the front door assembly, perform the fitting adjustment. Refer to
842, "DOOR ASSEMBLY : Adjustment"
.
• After installation, apply touch-up paint (the body color) onto the head of the door hinge mounting
nuts.
• Check the door hinge rotating part for poor lubrication. If necessary, apply body grease.
• Check the front door open/close operation after installation.
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000001098493
1.
Door check link
2.
Door hinge (upper)
3.
Door check link cover
4.
Door hinge (lower)
5.
Bracket
6.
Bumper rubber
7.
Front door panel
8.
Door striker
Refer to
JMKIA0179ZZ
DLK-510
< ON-VEHICLE REPAIR >
[WITH I-KEY & SUPER LOCK]
FRONT DOOR
DOOR CHECK LINK : Removal and Installation
INFOID:0000000001098495
REMOVAL
1.
Remove the front door finisher. Refer to
INT-10, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove the front door speaker. Refer to
AV-34, "Removal and Installation"
3.
Remove the mounting bolts of the door check link on the vehicle.
4.
Remove the door check link cover, and then remove the door check link mounting bolts.
5.
Remove the door check link.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check the front door open/close operation after installation.
1.
Door check link
2.
Door hinge (upper)
3.
Door check link cover
4.
Door hinge (lower)
5.
Bracket
6.
Bumper rubber
7.
Front door panel
8.
Door striker
Refer to
for symbols in the figure.
JMKIA0179ZZ
PIIB6543E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст