Nissan Qashqai (2007-2010). Manual — part 59
EM-184
< ON-VEHICLE REPAIR >
[MR20DE]
OIL SEAL
2.
Install rear oil seal so that each seal lip is oriented as shown in
the figure.
• Press-fit rear oil seal with a suitable drift outer diameter 113
mm (4.45 in) and inner diameter 90 mm (3.54 in) (A).
CAUTION:
• Be careful not to damage crankshaft and cylinder block.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
• Never touch grease applied onto oil seal lip.
• Press in rear oil seal (1) to the position as shown in the figure.
3.
Install in the reverse order of removal, for the rest of parts.
A
: Dust seal lip
B
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
PBIC3951E
A
: Rear end surface of cylinder block
PBIC3761E
CYLINDER HEAD
EM-185
< ON-VEHICLE REPAIR >
[MR20DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CYLINDER HEAD
Exploded View
INFOID:0000000000893956
REMOVAL
DISSASEMBLY
1.
Cylinder head assembly
2.
Cylinder head bolt
3.
Cylinder head gasket
A.
Refer to
PBIC3542J
PBIC3543J
EM-186
< ON-VEHICLE REPAIR >
[MR20DE]
CYLINDER HEAD
Removal and Installation
INFOID:0000000000893957
REMOVAL
1.
Release fuel pressure. Refer to
.
2.
Drain engine coolant and engine oil. Refer to
3.
Remove the following components and related parts.
• Exhaust manifold: Refer to
• Intake manifold: Refer to
.
• Fuel tube and fuel injector assembly: Refer to
.
• Water outlet: Refer to
.
• Rocker cover: Refer to
• Front cover, timing chain: Refer to
.
• Camshaft: Refer to
.
4.
Remove cylinder head.
• Loosen mounting bolts in reverse order as shown in the figure.
• Using TORX socket (size E18), loosen cylinder head bolts.
5.
Remove cylinder head gasket.
INSTALLATION
1.
Install cylinder head gasket.
2.
Install cylinder head, and tighten cylinder head bolts in numeri-
cal order as shown in figure with the following procedure.
CAUTION:
If cylinder head bolts are re-used, check their outer diame-
ters before installation. Refer to
.
a.
Apply new engine oil to threads and seating surface of mounting
bolts.
b.
Tighten all bolts.
1.
Valve collet
2.
Valve spring retainer
3.
Valve spring (EXH)
(with valve spring seat)
4.
Valve oil seal
5.
Valve guide (EXH)
6.
Valve seat (EXH)
7.
Valve (EXH)
8.
Valve (INT)
9.
Valve seat (INT)
10. Cylinder head
11. Valve guide (INT)
12. Spark plug
13.
Valve spring (INT)
(with valve spring seat)
A.
B.
Refer to
Refer to
for symbols shown in the figure.
: Engine front
PBIC3206J
: Engine front
: 40.0 N·m (4.1 kg-m, 30 ft-lb)
PBIC3206J
CYLINDER HEAD
EM-187
< ON-VEHICLE REPAIR >
[MR20DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
c.
Turn all bolts 100 degrees clockwise (angle tightening).
CAUTION:
Check and confirm the tightening angle by using an angle
wrench [SST: KV10112100] (A) or protractor. Never judge by
visual inspection without the tool.
d.
Completely loosen.
CAUTION:
In this step, loosen bolts in reverse order that indicated in
the figure.
e.
Tighten all bolts.
f.
Turn all bolts 100 degrees clockwise (angle tightening).
g.
Turn all bolts 100 degrees clockwise again (angle tightening).
3.
Install in the reverse order of removal, for the rest of parts.
Disassembly and Assembly
INFOID:0000000000893967
Disassembly
1.
Remove spark plug with spark plug wrench (commercial service tool).
2.
Remove valve lifter.
• Identify installation positions, and store them without mixing them up.
3.
Remove valve collet.
• Compress valve spring with valve spring compressor, attach-
ment and adapter [SST: KV10116200] (A). Remove valve col-
let with a magnet hand.
CAUTION:
Be careful not to damage valve lifter holes.
4.
Remove valve spring retainer and valve spring (with valve spring seat).
CAUTION:
Never remove valve spring seat from valve spring.
5.
Push valve stem to combustion chamber side, and remove valve.
• Identify installation positions, and store them without mixing them up.
6.
Remove valve oil seal with a valve oil seal puller [SST:
KV10107902] (A).
7.
When valve seat must be replaced.
: 0 N·m (0 kg-m, 0 ft-lb)
: 40.0 N·m (4.1 kg-m, 30 ft-lb)
PBIC3208J
PBIC3209J
PBIC3210J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст